Equipment

The LOIP LT-112a modification device consists of an immersion thermostat-circulator LOIP LT-100 and a working bath with a flat removable lid. Design features: The LOIP ATC intelligent control system adapts the parameters of the PID controller to the type of working fluid and eliminates the influence of instability of the mains voltage and air temperature on the operation of the system. A productive discharge pump ensures efficient mixing of the coolant inside the bath and high accuracy of maintaining the temperature of an external object with a closed circuit. A bright LED digital display displaying the current and set temperature with a discreteness of 0.1 °C. Multifunctional control knob. Simple correction of the internal temperature sensor readings with the possibility of calibration by two points. A cooling coil connected to the water supply to reach temperatures below room temperature (installed on request, not included as standard). Self-diagnosis system with indication of the causes of malfunctions on the display. A safety device with a sound and light notification that provides automatic shutdown of heating in the event of a break in the temperature sensor circuit, as well as when the coolant level drops below the permissible level. Stainless steel working baths, made by stamping, are characterized by a long service life and ease of cleaning. The external body of the bath is made of powder-coated steel and is reliably insulated from the tank of the bath, which allows the operator to work safely with the equipment even at high temperature of the working fluid. Technical specifications: Temperature range: without external cooling, °C Current +10 ... +100 with tap water cooling °C Tvods+5 ...+100 Accuracy of temperature maintenance, °C ± 0.1 The error of setting the set temperature, no more than ° C ± 0.2 Heater power, W 1900 Pump: max. flow rate, l/min 7.5 pressure, 0.17 bar Bath volume, l 12 The working fluid is water, water-glycerin mixture. Open part of the bath / depth, mm 190x296/150 Overall dimensions, mm 355x335x370 Weight, kg 10.2

It is designed to maintain temperature when determining the kinematic viscosity of petroleum products with glass viscometers in accordance with GOST 33, GOST R 53708, ASTM D445, IP 71, ISO 3104 and DIN 51366 and when determining the pour point of petroleum products in accordance with GOST 20287. Operating temperature range -30...+50 °C Four places for glass viscometers or a basket for determining the pour point of petroleum products. Stability and uniformity of temperature in the working bath is not worse than ± 0.01 ° C. Bath volume 15 l Overall dimensions 440x710x620 mm The open part of the bath is 140x170 mm Bath depth 320 mm The size of the viewing window is 104x270 mm Weight 56 kg Power consumption 3.5 kW

DPSS lasers of the KLM-415/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes. Technical specifications Radiation output power: up to 10W Radiation wavelength: 415 nm Output beam diameter: 1.5mm Divergence of the radiation beam: 1.3 mrad Instability of radiation power: 5% Type of modulation: TTL or analog Time to enter the mode: 15min Spectral line width: 0.1nm

Designation VCHV-15 Cooling capacity at Two.water= +15C, Tcond=+45C, Current.cp.=+30C, kW 15 Required pump capacity, m3/h 3.3 Pressure loss in the heat exchanger, kRa 65

Design features: Durable ceramic muffle; Closed heaters on four sides of the chamber; Microprocessor temperature controller; Conveniently located control panel and bright LED display; Ease of management and control; LED indicators of heater operation and protection operation; Automatic shutdown of heating when opening the door; Alarm when the current temperature exceeds the limits of the permissible range; Highly efficient thermal insulation of the housing; The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint. Technical specifications: Maximum heating temperature, °C +1100 Temperature stability in steady-state thermal mode, °C ± 10 Warm-up time to maximum temperature, no more than 120 min Dimensions of the working chamber, WxHxD, not less than 120x97x195 mm Overall dimensions, WxHxD, not more than 400x535x510 mm Rated supply voltage, 220 V Rated power, W 2200

Electric Furnace SNVS-14.20/12- I3B is designed for medium vacuum heat treatment of parts made of carbon, stainless and high-strength steels (such as VT-1-0, OT-4, VT6C, VT-23, etc.), magnetic materials to obtain a light surface of the part, as well as quenching during vacuum cooling. The furnace can be used with the maximum dimensions of the cage: diameter — 1400 mm, height — 2000 mm for annealing particularly precise axisymmetric parts (cones, cylinders, shells of double curvature). • Execution of the electric furnace — shaft. • The type of cage is monoblock or composite. • The loading direction is vertical. • Loading method — universal shop lifting mechanisms. The furnace is controlled by an industrial controller with installed software. The technological parameters of the product, the controls are displayed as a graphical mnemonic on the monitor. With touch control. It provides the setting of thermal parameters, the ability to save programs, the ability to save graphs by date, view and remove the archive to an external USB drive. The technical process will be carried out according to the program entered into the control panel or PC of the vacuum electric furnace, with the ability to adjust the values of temperature, exposure time. The electric furnace provides for operation in automatic and manual modes.

It is designed to maintain a set temperature of a liquid coolant circulating both in an internal bath and in external consumers of a closed or open type. Pump for closed or open type thermostating systems. All-metal stamped tub with a volume of 10 liters and a depth of 200 mm. The stability and uniformity of the temperature in the inner bath is not worse than ± 0.1 ° C. The operating temperature range is +20...+200 °C. The volume of the bath is 10 liters Overall dimensions 400x275x480 mm The open part of the bath is 120x200 mm Bath depth 200 mm Weight 14 kg Power consumption 2.2 kW

The analyzer allows you to determine the content of sulfur and nitrogen in oil and petroleum products (diesel fuel, gasoline, kerosene, gas oil and any distillate petroleum products), hydrocarbon gas, liquefied petroleum gas (LPG), natural gas, liquefied natural gas (LNG), chemical synthesis products, biological materials by ultraviolet fluorescence and chemiluminescence. The analyzer is a proprietary development of NPO "SPEKTRON". The device is manufactured in St. Petersburg mainly from domestic components. There is a conclusion of the Ministry of Industry and Trade on the production of products in the territory of the Russian Federation. The analyzer is designed to determine: - mass fraction of sulfur in accordance with GOST ISO 20846-2016, GOST 34712-2021, GOST R 56866-2016, GOST 34237-2017, ASTM D5453-19, ASTM D6667-21, ASTM D7551-15, ISO 20729-17 ; - the mass fraction of nitrogen in accordance with ASTM D4629-17. A wide range of concentrations: from ultra-low to high. Modular principle: Each detector is a separate module. The device is equipped individually for each specific task. The possibility of simultaneous determination of sulfur and nitrogen in the analysis process. The principle of operation of the analyzer is to burn the test sample in an oxygen-enriched atmosphere or air at a temperature of 1050 ° C. The sulfur dioxide (SO2) and nitrogen oxide (NO) formed during combustion are transferred by carrier gas to the detection units with preliminary removal of water vapor, on the desiccant, and soot, on the filter. Determination of sulfur is carried out by ultraviolet fluorescence. Determination of nitrogen by chemiluminescence.

The characteristics of the device are similar to the GVCH-12M1 model. The difference is the generator capacity of 16 liters /hour. Technical specifications Purity of hydrogen in terms of dry gas is about 99.9999% The concentration of water vapor at 20 ° C and 1 atm is not more than 5 ppm In the output pressure stabilization mode The range of the specified output pressure of hydrogen is from 1.5 to 6.1 ati Stability of the output pressure of hydrogen is not worse than ± 0.02 ati Maximum hydrogen capacity reduced to normal conditions is 16 l/h The time of setting the operating mode, with the output turned off is no more than 30 min In the performance stabilization mode: The range of the specified hydrogen performance is from 0 to 16 l/h Maximum developed pressure in performance mode is 5.0 ati Volume of distilled water to be poured is 1.0 l Distilled water consumption is no more than 0.025 l/hour, Water consumption is 1.6 g/l of hydrogen The average life of a replaceable deionization filter cartridge (at maximum performance and single-shift operation) is at least 1 year Average power consumption: in stationary mode is no more than 200 VA maximum (at startup) is no more than 250 VA Overall dimensions of the generator, (width x depth x height) are not more than 230x470x450 mm The mass of the generator is not more than 16 kg Operating conditions: ambient temperature, °C, from +10 to +35 powered by single-phase AC voltage, V, 220 (+10 -15)% and frequency, Hz, 50 ± 1 The generator for electrical safety meets the requirements of Class 1, type H according to GOST 12.2.025-76

The SNVS-25/5 vacuum drying cabinet with a volume of 25 liters with manual vacuum adjustment is designed for heat treatment of materials at temperatures up to 500 with air access and in a vacuum controlled by manual valves. Thanks to modern temperature control, it demonstrates excellent performance of heat treatment modes. The measurement system complies with Russian standards and has certificates of entry into the SI State Register. Design for heat treatment in production and clean laboratories. The cabinet can be equipped with a software control device with an automatic timer and a wide selection of additional options.

The AG-107 generator is designed to create alternating current in electrically conductive communications with the electromagnetic method of tracerouting. Features of the AG-107 generator The main distinguishing feature is the small weight and dimensions of the device with high output power. The AG-107 generator has a built-in battery based on light high-capacity lithium-iron phosphate (LiFePO4) cells with low self-discharge, dimensions 216x180x105 mm, weight 1.8 kg and provides the following maximum output parameters: The output power in continuous operation is 30 watts; output power in intermittent operation mode is 60 W; Output voltage 60 V; current 5 A. The AG-107 generator uses a control interface similar to the AG-105 generator. The generator implements: Four sine wave generation frequencies: 512 Hz, 1024 Hz, 8192 Hz and 33 kHz; continuous, pulse and dual-frequency generation modes; built-in transmitting antenna operating at frequencies of 8192 Hz and 33 kHz; the possibility of connecting an external transmitting antenna and induction tongs; built-in "multimeter" displaying, at the operator's choice, the supply voltage or output parameters: current, power, voltage, load resistance; the ability to work from an external battery or from the mains ~ 220 V. The generator can be operated from an external power supply of 10...25 V. The generator is protected from the effects of voltages up to 400 V when connected to the communication and from exceeding the permissible voltage of the external power supply. The degree of protection of the case - case IP65 completely eliminates the penetration of dust and water jets inside when the lid is open.

Displaying the spectra and dose rates measured by each detection unit (DB) on the object plan or terrain map Identification of the radionuclide composition of the source The possibility of expanding the energy range up to 5 MeV Sealed DB design (IP68) Backup power supply