Equipment

The spectrometer is designed to perform quantitative and qualitative spectral analysis of various substances and materials (powders, metals, solutions) in factory and research laboratories. The spectrometer is compact due to the vertical arrangement of the Paschen-Runge optical system. It consists of two MAES analyzers with 10 lines of photodiodes installed on a circle with a radius of 520 mm, a non-classical concave diffraction grating, a special table with a built-in computer and a spectrum excitation source.

CDL lasers of the KLM-355-x series are optimal sources of continuous radiation for the construction of control and automation systems, for scientific and medical purposes.

The operating temperature range is -30...+105 °C. The stability and uniformity of the temperature in the working bath is not worse than ± 0.01 ° C without the use of a leveling unit. Bath volume 13 l Overall dimensions 450x700x810 mm The open part of the bath is 90 mm Bath depth 430 mm Weight 70 kg Power consumption 3.5 kW

Designation SNO-40 Volume, l 40 The material of the working chamber is ceramic Heating 4 sides Power consumption, W, max 10000 Minimum operating temperature, 0C 100

The 3VVN2-50(H) water ring vacuum pump is not intended for use in fire and explosion hazardous industries. The 3VVN2-50(H) vacuum water ring pump is manufactured in the climatic version of UHL 4 and O4 (i.e. for moderate and cold climate) according to GOST standard 15150-69, meets the requirements of technical specifications TU 3648-053-00218526-2013, designed and manufactured taking into account the requirements of GOST R 52615-2006.

Allows you to simultaneously place up to 4 hydrometers and a thermometer. A low-temperature liquid thermostat is additionally required to ensure the temperature of the calibration liquid of 20 ±0.05 °. Overall dimensions 500x380x650 mm The open part of the bath is 135 mm Bath depth 490 mm Weight 27 kg

The principle of operation is based on measuring the zonal reflection coefficient of a compacted-smoothed flour surface using a built-in standard. The laboratory white meter BARS is approved as a type of measuring instruments and is registered in the State Register of Measuring Instruments under No. 78409-20. All manufactured devices undergo primary verification and have the appropriate certificate. Due to the two-channel design of the device (the presence of two photometric units and a cuvette with two cells), parallel measurements of the whiteness of one flour sample are carried out simultaneously, the average value is calculated automatically, which significantly reduces the time of analysis. The sealing of the flour sample with a fixed force and pressing against the optical windows ensures the same measurement conditions and eliminates the influence of a subjective factor on the result. The automatic adjustment system based on the built-in standard allows to ensure long-term stability of the device without the need for manual adjustment. During operation, the standard is set to the working position by an additional drive. Mechanical damage or loss of the standard is excluded. The output to the operating mode is no more than 30 seconds. The determination of whiteness is carried out in 15 seconds. To determine the whiteness of flour, the operator needs to fill 2 compartments of the cuvette with the test sample of flour, install the cuvette in the device and start the measurement process. All the results of the whiteness definitions are stored in the archive. The operator has the opportunity to view the electronic measurement log.

The small-sized digital magnetometer (Gaussmeter, teslameter), ION-3701 residual magnetization meter is a modern high-precision instrument, a further development of ION series devices (ION-1, ION-2, ION-2M, ION-7) and used for a wide range of tasks in areas where it is necessary to determine the magnitude of the magnetic field and residual magnetization. It is equipped with a three-dimensional magnetic field sensor and has outstanding technical characteristics and extensive functionality.

They are designed for carrying out various technological processes at temperatures from 40 to 500 oC, in vacuum up to 1x10−3 mmHg, or in an inert gas of high purity. They are used for drying, light annealing, aging, low and medium tempering in an oxidizing environment, degassing of ferrous and non-ferrous metals (including copper and copper alloys), or any other materials processed under similar conditions. The program setting of heat treatment modes including vacuuming, high purity inert gas intake with repeated vacuuming allows heating in an oxidizing environment with high purity of the surfaces of the processed parts, without scale formation and oxidation.

Laboratory Low-temperature Precision Drying Cabinet SNOL-7.4.7/1,0- I2-B is designed for long-term heat treatment (and storage) in a stirred air environment at temperatures up to 100 ° C.

Technical specifications: The range of set unit temperatures, °C from +50 to +250 Accuracy of temperature maintenance, °C ± 1 Time to reach a temperature of 162 ° C, no more, min. 40 Air consumption, l/min 180±32 Voltage, 220 V Power, W 2000 Overall dimensions, mm 410x305x250 Weight, kg 20