Equipment

The measurement range of arsenic in waters, soil, and food products allows the determination of arsenic at concentrations well below the permissible level (maximum permissible concentration).

a massive copper mold was used in the furnace, as well as a printed crucible made of stabilized (calcium oxide) zirconium dioxide. The furnace has been working for several years at one of the non-ferrous metallurgy enterprises in the production of platinum ingots according to GOST

The working condition of the ND-400(R) diffusion pump depends on the temperature of the working fluid in the pump boiler. During the initial filling, it is recommended to fill the maximum volume of the working fluid. Working fluid is "VACMA OIL 500" vacuum oil (under technical specifications TU 19.20.29-061-00218526-2019). The total amount of working fluid in the ND-400(R) diffusion pump is a maximum of 5 liters, a minimum of 3.3 liters. The viewing window for visual inspection of the working fluid has marks of its maximum and minimum amounts. During normal operation of the pump, the level of the working fluid practically does not change. The temperature of the working fluid when the pump is operating at the maximum residual pressure is about 240°C to 255°C. It is recommended to monitor the operation of heaters in the ND-400(R) diffusion pump using one temperature sensor. The temperature sensor must be installed in a special radiator socket above the heater. If there is a loss of working fluid and an increase in the temperature of the radiators of the ND-400(P) diffusion pump to 320°C, the temperature sensor must give the command to automatically turn off the heaters. The subsequent activation of the pump heaters should not be automatic and should be performed only after cooling the system. Water at the inlet to the cooling systems of the housing and the oil reflector must be supplied with a pressure of 0.3 MPa (3 kgf/cm2) to 0.5 MPa (5 kgf/cm2) and a temperature of plus 4°C to plus 25°C. The recommended cooling water consumption for the housing is 250 l/h, for the oil reflector it is 40 l / h. It is regulated by the outlet water temperature, which should not exceed plus 40°C. The water drain should be free (with a jet break).

Capacity: 25.0 (- 10%) l/h Heating elements: Heating ELEMENT 2.6 kW 220V (stainless steel) – 6 pcs. The quality of the produced water: FS.2.2.0019.18 "Water for injection", GOST R 58144- 2018 "Distilled water" Type of current, frequency, voltage: three-phase alternating, 50 Hz, 380 V Power consumption: 15.0 kW Overall dimensions (L×W×C), mm: 355×310×580 Weight: 15.6 kg Warranty period: 24 months from the date of sale Registration certificate for a medical device No. FSR 2010/07649 of November 01 , 2016 Electrical conductivity of the produced water: 2-2.5 microns/cm The temperature of the produced water: from 70 to 85 ° C Source water flow rate (at 10 °C water temperature): 180 (±10%) l/h Source water pressure: 0.1-0.4 MPa Overall dimensions of the control unit (L×W×C), mm: 255×95×200 Version: Desktop with adjustable supports, Wall mounted (bracket is purchased separately) Coefficient of water purification from radionuclides: at least 4000 Service life: at least 10 years

It is designed to maintain a set temperature of a liquid coolant circulating both in an internal bath and in external consumers of a closed or open type. Pump for closed or open type thermostating systems. With a set of devices VT20-4K can be used for testing samples of asphalt concrete and oil bitumen. The operating temperature range is +20...+200 °C. Bath volume 20 l Overall dimensions 490x330x450 mm The open part of the bath is 240x200 mm Bath depth 210 mm Weight 16 kg Power consumption 2.2 kW.

It is designed to maintain the set temperature of the coolant circulating in the internal bath of the thermostat and in the connected external consumers. Feed pump for external closed-type thermostating systems. Cooling capacity 250 W at +20 °C. An internal bath with a volume of 6 liters and a depth of 140 mm. The operating temperature range is -20...+200 °C. Overall dimensions 280x460x620 mm The open part of the bath is 110x80 mm Bath depth 140 mm Weight 34 kg The power consumption is 2.5 kW.

Technical specifications: Melt flow rate for 10 min, g 0,1 - 99,9 The dimensions of the capillary opening, mm dia. 2,095 diam. 1,048 (optional) diam. 1,180 (optional) Set of loads, kg 0,325-5 10-21,6(optional) Temperature range in the working chamber, °C +50...+450 Accuracy of temperature maintenance, °C: - in the range of 50...300 °C: ± 0.1 - in the range of 300...350 ° C: ± 0.2 - in the range of 350...450°C: ±0.3 The discreteness of setting the temperature of the chamber, ° C 1 Time to enter the operating mode, no more, min 40 Power supply, V/kW 220/0.8 Installation dimensions, WxDxH mm 513x445x590 (920 – Maximum height with a fully loaded polymer chamber and a full stack of loads with a handle for their installation) Installation weight, not more than 70 kg

The service life of the furnace at a temperature of 1800 OC is not less than 500 hours; number of thermal cycles, not less than 100

Optical transceivers are available in 9-pin plastic cases with a single optical input/output for SC type connectors.

Purpose: obtaining distilled water of type 2 according to GOST R 58144-2018 "Distilled water", FS.2.2.0019.18 "Water for injection" Capacity: distillate: 9.0 (-10%) l/h, bidistillate: 8.0 (-10%) l/h Heating elements: 1st stage of distillation: Heating element 2.0 kW 220V (stainless steel) – 3 pcs., 2nd stage of distillation: Heating element 1.8 kW 220V (stainless steel) – 3 pcs. The quality of the produced water: GOST R 58144-2018 "Distilled water", FS.2.2.0019.18 "Water for injection" Type of current, frequency, voltage: alternating, single-phase, 50 Hz, 380 V Power consumption in distillate production mode: 6.0 kW, in bidistillate production mode: 11.4 kW Overall dimensions (L×W×C), mm: 675×365×470 Weight: 30.0 kg Warranty period: 12 months from the date of sale Electrical conductivity of the produced water: bidistillate: 1.0-1.2 microns/cm, distillate: no more than 5.0 microns/cm The temperature of the produced water: distillate: from 70 to 85 ° C, bidistillate: no more than 40 ° C Source water consumption (at t of water 10 ° C) in the distillate production mode: 72.0 (±10%) l/h, in the bidistillate production mode: 168.0 (±10%) l/h Source water pressure 0.1-0.4 MPa Version: Desktop with adjustable supports. Wall mounting is possible Coefficient of water purification from radionuclides: at least 4000 Service life: at least 8 years

Cooling capacity at water temperature = +20C, output.water=+15C, Current.cp.=+30C, 300 kW

The trace searching kit is designed to accurately determine the location and depth of underground utilities (power and signal cable lines, reinforced fiber-optic lines, pipelines made of electrically conductive materials), troubleshooting cable lines, and also allows you to conduct a survey of the area in the shortest possible time and with great reliability before excavation and to prevent damage to engineering communications. As part of the kit, the receiver is in the form of a monoblock with a frost-resistant LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line. Compact stand-alone generator with display and built-in induction antenna. The output power of the generator is up to 20 watts and the operating range is up to 3 km.