Accessories

Partially universal detector. It is used for the analysis of most organic compounds, including aromatic and aliphatic (except methane) hydrocarbons, heterocyclic compounds, phenols, phthalates, pesticides, amines, ketones, aldehydes, esters, mercaptans. It does not register compounds whose ionization threshold is higher than 10.2 eV (for example, acetonitrile, methanol). Technical characteristic: 5.0*10`13 g/s for benzene

The TDS-3 includes a heating column with a sorption tube, which is installed on the evaporator of the chromatograph and a control unit located on a special bracket on the right side panel of the chromatograph Technical characteristics of TDS-3 Desorption temperature (column heating), 0C to 400 Heating speed, 0C/min at least 500 The cooling time when moving to a cold zone is no more than 10 seconds. Cooling time from 300 0C to 50 0C, min. no more than 10 Continuous operation mode Power consumption, W not more than 250 Dimensions of the sorption tube, (Ø, length), mm. Material glass, stainless steel 5/110, 5/114, 6/115, 6.35/89 Electric power supply from 187 to 242 V, 50 Hz. The display of the measured temperature and the setting of the temperature on the display is The discreteness of setting the desorption temperature, 0C 0.1

Scope of delivery of the laboratory: — viscometer VBR-2; — lever scales VRP-1M; — glass, 1000 ml; — pH strips, pH 1-14, 100 pcs./pack; — electronic stopwatch; — determination of the sand content.

The probe is designed for use with leak detectors of any type, which have an input port NW (KF) 25 and provide a counterflow mode of operation.

Основные характеристики Диапазон измерения температуры, °С От -70 до + 200 Погрешность измерения температуры, °С, не более 1 Номинальное сопротивление при 25 С,кОм 1.0 Длина рабочей части PT 1000 (погружной) 250 мм Длина ручки 50 мм, диаметр ручки М12 Длина провода до 600 мм

Main characteristics Temperature measurement range, °C From -70 to + 300 Temperature measurement error, °C, no more than 1 Nominal resistance at 25 C, kOhm 1.0 Dimensions, weight Height 40 cm Sensor projection from the stand is 16 cm

Variants of execution: - silica gel with grafted octadecyl groups (C18, RP, ODS) - for the variant of reversed-phase HPLC (OF HPLC); - unmodified silica gel (SIL) – for normal-phase HPLC (NF HPLC).

It is intended for the preparation of samples in the form of compressed tablets consisting of the test substance in a mixture with microcrystalline potassium bromide (KBr). The mold is used in combination with the hydraulic press GP 200-13. - the mold is made of high-quality alloy hardened steel - to obtain better compressed tablets with KBr, the mold can be pumped out using a pre-vacuum pump. The customer can purchase the pump independently, or order it from the NPF “SIMEX”. Pumping out the mold is not necessary for most studies. - the kit includes a special dispenser for placing the optimal amount of the pressed mixture in the mold - to install the finished samples in the spectrometer, a holder of KBr tablets and D13mm substrate windows is used

They are used for the study of liquids, including solutions with low concentrations • Have a collapsible design that allows you to use the supplied gaskets of different thicknesses • Window material – ZnSe (it is possible to order windows from SiO2 and KBr) • Gasket material – Teflon (fluoroplast) • Thickness of gaskets – 0.022 mm, 0.1 mm, etc.

Single- and multi-pass flask are used for qualitative and quantitative spectral analysis of gas mixtures. The use of multi-pass flask makes it possible to confidently detect extremely small concentrations of the components of the gas under study (less than ppm units). • Three types of flask are supplied: 1. single-pass, having a stroke length of 100 mm, with a glass body and windows made of ZnSe, KBr, NaCl 2. multi-pass, with a beam stroke length of up to several tens of meters 3. multi-pass, with a beam stroke length of up to several tens of meters, equipped with a heating system of the working chamber up to 200 ° C and a thermal controller Multi-pass cuvettes have a transparent working chamber made of quartz glass; mirrors with a gold (99.999) coating provide a reflection coefficient in the IR region of at least 98%; additionally, cuvettes can be equipped with pressure and temperature sensors, fittings for controlling gas flow, etc.