Equipment

It is designed to maintain a set temperature of a liquid coolant circulating both in an internal bath and in external consumers of a closed or open type. Pump for closed or open type thermostating systems. All-metal stamped tub with a volume of 15 liters and a depth of 200 mm. The stability and uniformity of the temperature in the inner bath is not worse than ± 0.1 ° C. The operating temperature range is +20...+200 °C. Bath volume 15 l Overall dimensions 420x330x480 mm The open part of the bath is 150x260 mm Bath depth 200 mm Weight 16 kg Power consumption 2.2 kW.

The serological bath SB-SL-01M replaced the BSL bath. The sauna is designed to perform laboratory tasks that require maintaining a constant temperature. The bath is perfect for serological studies, allowing to install 4 Florinsky tripods of 100 test tubes. The bath is made of high-alloy stainless medical steel. The bath body has double thermal insulation with a low coefficient of thermal conductivity. The heating element is located at the bottom of the bath over the entire working area of the bath, which allows for uniform heating of the working fluid and stable maintenance of the set temperature regardless of fluctuations in ambient temperature and the frequency of opening and closing of the lid. The warranty for the bath is 5 years. Microprocessor temperature controller with controller and touch control keys. The heating element is protected from overheating (for example, in case of a decrease in the water level). The control unit is equipped with indicators for turning on the heater and emergency operation of the protective circuit.

Devices of a new generation, automated stations of continuous radiation monitoring Zastava-1 are designed to organize continuous effective monitoring of the radiation situation and notification of radiation hazards. The stations have up to three independent measurement channels, which allows monitoring simultaneously in several zones. The stations support remote monitoring - they have a connection to a local computer network, Internet access.

DPSS lasers of the KLM-405/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes. Technical specifications Radiation output power: up to 10W Radiation wavelength: 405 nm Output beam diameter: 1.5mm Divergence of the radiation beam: 1.3 mrad Instability of radiation power: 5% Type of modulation: TTL or analog Time to enter the mode: 15min Spectral line width: 0.1nm

The MS-1104E spectrometer is characterized by high performance and accuracy of Mössbauer measurements achieved through the use of “compressed” geometry, as well as the use of highly efficient and selective resonant scintillation detection units that improve the energy resolution of resonance absorption lines by up to 30%. The technique of software and hardware stabilization of the spectrometric path developed and used in the spectrometer allows for long-term Mossbauer measurements without manual adjustment. The method of modulation in the specified speed intervals can significantly increase the sensitivity and expressiveness of measurements and reduce the time to determine the magnitude of the effects of resonant absorption by tens of times in the study of temperature phase transitions with a low concentration of resonant elements. The electronic components of the spectrometer are developed on the basis of a modern element base using programmable logic matrices and microprocessors. Adjustable spectrometric paths and high-voltage power supplies of the PMU are integrated into detection units, modulator driver modules and multi-channel storage are made in the ISA standard and are located in the processor unit of the computer. Setting and monitoring of all parameters of the spectrometer and processing of the measured spectra is carried out from the operating windows of the control and processing programs. Since 2000, more than ten spectrometers of this type have been supplied to leading scientific organizations in Russia and neighboring countries. One of the few industrial applications of Mössbauer spectroscopy should be noted - the development and supply to the Volgodonsk NPP of certified MS-1104Em methods and spectrometer for monitoring corrosion processes in the heat exchange circuits of the VVER-1000 reactor.

An oxygen adsorption station for refueling cylinders is a set of special equipment designed for the production and subsequent refueling of oxygen into cylinders or monoblocks obtained from atmospheric air by short—cycle non-heating adsorption. Unlike the installation, the station is equipped with an oil-free booster compressor, which creates the necessary pressure. Put the squeeze on the compressor. Provita's adsorption stations allow producing oxygen with a purity of up to 99.0%. As a rule, the filling of production gas into cylinders is carried out up to a pressure of 150-200 bar. Composition: 1. Air compressor 2. Dehumidifier 3. Main filter block 4. Air receiver 5. Oxygen generator 6. Oxygen receiver 7. Oil-free booster compressor putting the squeeze on 8.Gas filling ramp

Detection of SCR in all possible range of its characteristics High reliability Self-monitoring of components Backup power supply Recording and storage of measurement results in the non-volatile memory of the device The possibility of integration with external security systems DRG-AT2331 together with SRK-AT2327, personal computer and software "SARK.NET " allows you to form an alarm system for detecting the occurrence of a self-sustaining chain reaction (SAS SCR).

The LOIP LT-117a modification device consists of an immersion thermostat-circulator LOIP LT-100 and a working bath with a flat removable lid. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +100 with tap water cooling °C Tvods+5 ...+100 Accuracy of temperature maintenance, °C ± 0.1 The error of setting the set temperature, no more than ° C ± 0.2 Heater power, W 1900 Pump: max. flow rate, l/min 7.5 pressure, 0.17 bar Bath volume, l 17 The working fluid is water, water-glycerin mixture. Open part of the bath / depth, mm 360x296/150 Overall dimensions, mm 535x335x370 Weight, kg 13

The LOIP LT-412a modification device consists of an immersion thermostat-circulator LOIP LT-400 and a working bath with a flat removable lid. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +200 with tap water cooling °C Tvods+5 ...+200 Accuracy of temperature maintenance, °C ± 0.01 The error of setting the set temperature, no more, °C ±0.02 Heater power, W 2200 Pump: max. flow rate, l/min 6...12 pressure, 0.4 bar Bath volume, l 12 The working fluid is water, silicone oil. The open part of the bath / depth, mm 190x296/150 Overall dimensions, mm 355x335x350 Weight, kg 11.8

The vacuum trap of the condenser type FVC-1/15C with a capacity of 1 liter is designed for condensation and trapping of pumped vapors of epoxy resins and other substances that turn into a solid state during condensation, followed by removal of accumulated filtrate by washing with solvents or mechanical cleaning of a replaceable cartridge.

General monitoring of contamination of various objects with radioactive substances in the counting rate mode, with the possibility of separate measurement of the alpha particle flux density and beta particle flux density, as well as the gamma radiation dose rate A wide range of measurements The possibility of using an extension rod

Designation VCHV-10 Cooling capacity at Two.water= +15C, Tcond=+45C, Current.cp.=+30C, kW 10 Required pump capacity, m3/h 2,2 Pressure loss in the heat exchanger, kRa 40