Equipment

The voltmeter is capable of working both independently and as part of automated measuring systems with interfaces such as USB, RS-232, IEEE-488 (CPC). Technical specifications Measuring ranges of electrical quantities: - constant electrical voltage from 3 MV to 1000 V - SCR of alternating electric voltage in the frequency range from 10 Hz to 1 MHz (AC) from 10 MV to 1000 V - RF RF AC voltage in the frequency range from 10 Hz to 2000 MHz (RF) from 10 mV to 100 V - frequency of the measured AC voltage from 10 Hz to 1 MHz Measurement errors of electrical quantities: - constant electrical voltage ± (0.0021 - 17)% - SCR of alternating electric voltage in the frequency range from 10 Hz to 10 MHz (AC) ± (0.017 - 21)% - RF RF AC voltage in the frequency range from 10 Hz to 2000 MHz (RF) ± (0.21 - 16)% - frequency of the measured alternating electric voltage ± (0.1 -10.1)% General characteristics: Operating temperature range from 5 to 40 °C AC power supply 220 V, 50 Hz Power consumption, no more than 50 VA Overall dimensions, mm 489x91x381 Weight, not more than 8.5 kg

It is intended for thermostating samples in glasses, flasks and other laboratory utensils in cases when high accuracy of temperature maintenance is not required and good uniformity of the temperature field in the working volume is not needed. The operating temperature range is Current +5...+200 °C. Three workstations with a diameter of 110 mm with five steel O-rings. Stamped steel tub with a volume of 11 liters and a depth of 160 mm. Bath volume 11 l Overall dimensions 355x310x385 mm The open part of the bath is 295x235 mm Bath depth 160 mm Weight 9.5 kg Power consumption 2.5 kW

Design features: Programmable microprocessor temperature controller; Three programs of ten steps with the ability to set the temperature, heating speed and holding time for each step; Manual heating mode with timer with sound notification and auto-off; Durable ceramic muffle; Semi-open heaters on four sides of the chamber; Backlit graphic display; Conveniently located control panel; Automatic shutdown of heating when opening the door; Sound and light alarm when the current temperature exceeds the limits of the permissible interval; The door opens up and faces the user with the cold side; Highly efficient thermal insulation of the housing; The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint. Technical specifications: Maximum heating temperature, °C +1300 Temperature stability in steady-state thermal mode, °C ± 10 Warm-up time to the maximum temperature, no more than 120 min Dimensions of the working chamber, WxHxD, not less than mm 215x190x330 Overall dimensions, WxHxD, not more than mm 525x655x680 Rated supply voltage, 220 V Rated power, W 6100

Technical specifications: Limit of detection of the control substance (phenol) in water, mg/dm3, no more 0,005 Measurement range of the mass concentration of the control substance (phenol) in water, mg/dm3 from 0.01 to 25 Measurement range of the directional transmission coefficient, % from 5 to 100 Limits of permissible absolute error of measurements of the directional transmission coefficient, % ± 2 Warm-up time, min, no more than 30 Continuous operation time, h, at least 8 Overall dimensions, mm, no more than 305x320x110 Weight, kg, no more than 6.5 AC power supply: - AC power supply voltage, V - frequency, Hz (220 ±22) (50 ±1) Power consumption, In × A, no more than 36 Time to failure, h, not less than 2500

For primary and periodic verification and calibration at the field of operation of the following measuring instruments that are part of automated information and measurement systems for commercial accounting of electrical energy (AIIS KUE) or non-automated metering units: • – Measuring voltage transformers (TN) of accuracy classes 0.2 and less accurate at loads normalized by GOST, and at real loads at the metering unit. • – Measuring current transformers (TT) of accuracy classes 0.2S and less accurate with nominal primary currents of 100...5000 A (including high-voltage transformers for 330 kV lines) at loads standardized by GOST 7746-2001 and at real loads; single-phase and three-phase electric active and reactive energy meters of accuracy classes 0.2S and less accurate. • – Auxiliary SI: ammeters, voltmeters, wattmeters, voltage, current and power converters, accuracy classes 0.2 and less accurate, phase meters, power factor meters of accuracy classes from 0.10 and less accurate. • – Energy frequency meters of accuracy classes from 0.02 and less accurate, used at the electricity metering unit. • – For measuring the load capacity of TN iTT. • – For measuring voltage losses in secondary TN circuits. – For measuring the quality of electrical energy (PCE) in accordance with the requirements of GOST 13109-97.

KLM-C635-5-5 laser modules are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes.

The UPVD deionizer is suitable for enterprises, research centers and laboratories where type 2 water is required for laboratory analysis with an electrical conductivity of no more than 1.0 mcm/cm. Overall dimensions (LxWxH) 500×470×720 mm Weight 36.5 kg

The electric drying cabinet SHS-40/3.5 is designed for drying, heating various materials in an air environment at a maximum temperature of 350 ° C. Technical specifications The electric cabinet operates at ambient temperature from 10 to 35 ° C and relative humidity up to 80% at 25 ° C. Operating temperature- 350 ⁰C Power consumption - 2500 W Dimensions of the working chamber WxDxH- 390x360x390 mm Dimensions WxDxH- 600x630x580 mm Weight - 67 kg

Laboratory heating plate with two heating sections, with the possibility of setting the temperature and heating time, with a large heating surface area. The heating platforms are made of duralumin. The size of the total heating surface: 568x440 mm. Heating temperature of the plate surface: 40-400 oC.