Equipment

The operation of the NVDM-160 diffusion pump is based on the capture and transfer of the pumped gas by a steam jet flowing from the slit gaps of the steam line nozzles towards the outlet flange. The oil reflector of the NVDM-160 diffusion pump is a flange with a cooling tube passing through it, soldered to a cap located in the center of the flange. The NVDM-160 closed-type diffusion pump heater consists of tubular electric heaters fixed in the heater housing. During the operation of the pump, it is necessary to monitor the flow rate and temperature of the cooling water, the level of the working fluid and its temperature. Replacement or refilling of the working fluid depends on the operating mode of the pump (inlet pressure, pumping duration, etc.) and the composition of the pumped medium. Therefore, the time after which the working fluid is replaced or refilled can be from 100 to 1000 or more hours. A large flow rate of the working fluid is observed when the pump is operating in the range of inlet pressures from 6.6×10-2 to 13.3 Pa (from 5×10-4 to 1×10-1 mm Hg). Water at the inlet to the cooling systems of the housing and oil reflector must be supplied with a pressure of no more than 0.5 MPa (5 kgf / cm2) and temperature from plus 40C to plus 250C. The recommended cooling water consumption is 60+10 l/h and is regulated by the outlet water temperature, which should not exceed plus 400C. The water drain should be free (with a jet break). Not allowed: operation of the pump without water cooling, exceeding the maximum exhaust pressure of 33.3 Pa (0.25 mm Hg). The level of the working fluid during operation, at which the parameters of the NVDM-160 pump are provided, must correspond to min 10mm, max 17mm. The volume of the filled working fluid is 0.3 liters

The electric drying cabinet SHS-20/3,0 is designed for drying, heating various materials in an air environment at a maximum temperature of 300 ° C. Technical specifications The electric cabinet operates at ambient temperature from 10 to 35 ° C and relative humidity up to 80% at 25 ° C. Operating temperature- 300 ⁰C Power consumption - 2000 W Dimensions of the working chamber WxDxH- 195x480x195 mm Dimensions WxDxH- 325x760x445 mm Weight - 30 kg

The LOIP LT-424a modification device consists of an immersion thermostat-circulator LOIP LT-400 and a working bath with a flat removable lid. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +200 with tap water cooling °C Tvods+5 ...+200 Accuracy of temperature maintenance, °C ± 0.01 The error of setting the set temperature, no more than, ° C ± 0.02 Heater power, W 2200 Pump: max. flow rate, l/min 6...12 pressure, 0.4 bar Bath volume, l 24 The working fluid is water, silicone oil. Open part of the bath / depth, mm 360x296/200 Overall dimensions, mm 532x335x400 Weight, kg 15.8

Technical specifications: Type of motion orbital Platform rotation speed, min-1 40-300 The amplitude of rotation of the platform, mm 30 Maximum load on the platform, kg 20 Timer (time is displayed in h, min, s) 0...8 hours Power consumption, W 200 Platform size, mm 445x305 Overall dimensions, mm 525x510x225 Weight, kg 37

Drying cabinet with manual vacuum adjustment SNVS-90/3.5 (or SNVS-4,3.4,3.4.9/3,5) It is intended for heat treatment of materials at temperatures up to 350 ° C with air access and in a vacuum controlled by manual valves. Thanks to modern temperature control, it demonstrates excellent performance of heat treatment modes. The measurement system complies with Russian standards and has certificates of entry into the SI State Register. Design for heat treatment in production and clean laboratories.

The water treatment system (hereinafter referred to as the system) is used for the preparation of water used in hydrogen generators, for the preparation of solutions, chromatographic samples, capillary electrophoresis, high-performance liquid chromatography (HPLC), etc. analyzers requiring the use of high purity water. The system is connected directly to the municipal water supply line and allows obtaining high–purity deionized water with a specific electrical conductivity of 0.06 - 0.1 mcm/cm. The device uses multi-stage water purification. Technical specifications System output capacity, l/h not less than 6 Specific electrical conductivity of water, mcm/cm not more than 0.06 – 0.1 Power supply - single-phase AC 220V, 50/60 Hz Maximum power consumption, kW 0.1 Dimensions (W x D x H), mm 200 x 560 x 440 Weight, not more than 20 kg

They are designed for carrying out various technological processes at temperatures from 40 to 500 oC, in vacuum up to 1x10−3 mmHg, or in an inert gas of high purity. They are used for drying, light annealing, aging, low and medium tempering in an oxidizing environment, degassing of ferrous and non-ferrous metals (including copper and copper alloys), or any other materials processed under similar conditions. The program setting of heat treatment modes including vacuuming, high purity inert gas intake with repeated vacuuming allows heating in an oxidizing environment with high purity of the surfaces of the processed parts, without scale formation and oxidation.

Designation: SNO-12.18.12 Temperature: 1200 Opendoors: electromechanical Camera size (w.G.V.):1200x1800x1200 Regulation zones: 1

▪ Rapid adaptation to changes in the radiation background ▪ Audible and light alarms when gamma radiation is detected ▪ Mobility and the possibility of forming passages ▪ Self-control of components in the process of work ▪ The possibility of continuous or episodic radiation monitoring ▪ The possibility to work from a 230V, 50Hz network or from a built-in rechargeable battery Compliance with the international standard IEC 62244:2006 Stationary radiation monitors for the detection of radioactive and special nuclear materials at state borders

It is designed for thermostating samples in glasses, flasks and other laboratory utensils in cases when high accuracy of temperature maintenance is not required and good uniformity of the temperature field in the working volume is not needed. The operating temperature range is Current +5...+200 °C. Two workstations with a diameter of 110 mm with five steel O-rings. Stamped steel tub with a volume of 7 liters and a depth of 160 mm. The volume of the bath is 7 liters Overall dimensions 385x205x360 mm The open part of the bath is 295x145 mm Bath depth 160 mm Weight 7.5 kg Power consumption 2.5 kW

Temperature range, °C Current +5 ... +105 Accuracy of temperature maintenance, °C ± 1 Temperature setting error, °C ± 1 Power consumption from AC 220 V, max, 1600 W Number of jobs, pcs 4 The diameter of the workplace, mm 110 Volume of working fluid, l 10 Useful part of the bath / depth, mm 300x300 / 62 Overall dimensions, mm 400x310x140 Weight of the device without liquid is not more than kg 6

Design features: Programmable microprocessor temperature controller; Three programs of ten steps with the ability to set temperature, temperature change rates and exposure time; Manual heating mode with timer with sound notification; Reliable and stable Pt 100 temperature sensor; Four-sided heating; Forced air circulation in the working chamber; Camera material – stainless steel; Backlit graphic display; Conveniently located control panel; Sound and light alarm when the current temperature exceeds the limits of the permissible interval; Independent overheating protection circuit with separate temperature sensor; Reliable door closing mechanism; High-quality silicone sealer; Highly efficient thermal insulation of the housing; The case is made of high-quality sheet steel and painted with heat-resistant powder paint; Number of shelves: standard – 1, maximum – 5. Technical specifications: Maximum heating temperature, °C +350 The error of reproducing the set temperature ° C ± 3 Temperature maintenance error, ° C ± 1 Warm-up time to maximum temperature, no more, min 45 Dimensions of the working chamber, (WxHxD), not less than 250x275x250 mm Overall dimensions, (WxHxD), not more than 595x495x565 mm Rated supply voltage, 220 V Rated power, W 1200