Equipment

The serological bath SB-SL-01M replaced the BSL bath. The sauna is designed to perform laboratory tasks that require maintaining a constant temperature. The bath is perfect for serological studies, allowing to install 4 Florinsky tripods of 100 test tubes. The bath is made of high-alloy stainless medical steel. The bath body has double thermal insulation with a low coefficient of thermal conductivity. The heating element is located at the bottom of the bath over the entire working area of the bath, which allows for uniform heating of the working fluid and stable maintenance of the set temperature regardless of fluctuations in ambient temperature and the frequency of opening and closing of the lid. The warranty for the bath is 5 years. Microprocessor temperature controller with controller and touch control keys. The heating element is protected from overheating (for example, in case of a decrease in the water level). The control unit is equipped with indicators for turning on the heater and emergency operation of the protective circuit.

Devices of a new generation, automated stations of continuous radiation monitoring Zastava-1 are designed to organize continuous effective monitoring of the radiation situation and notification of radiation hazards. The stations have up to three independent measurement channels, which allows monitoring simultaneously in several zones. The stations support remote monitoring - they have a connection to a local computer network, Internet access.

DPSS lasers of the KLM-405/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes. Technical specifications Radiation output power: up to 10W Radiation wavelength: 405 nm Output beam diameter: 1.5mm Divergence of the radiation beam: 1.3 mrad Instability of radiation power: 5% Type of modulation: TTL or analog Time to enter the mode: 15min Spectral line width: 0.1nm

The MS-1104E spectrometer is characterized by high performance and accuracy of Mössbauer measurements achieved through the use of “compressed” geometry, as well as the use of highly efficient and selective resonant scintillation detection units that improve the energy resolution of resonance absorption lines by up to 30%. The technique of software and hardware stabilization of the spectrometric path developed and used in the spectrometer allows for long-term Mossbauer measurements without manual adjustment. The method of modulation in the specified speed intervals can significantly increase the sensitivity and expressiveness of measurements and reduce the time to determine the magnitude of the effects of resonant absorption by tens of times in the study of temperature phase transitions with a low concentration of resonant elements. The electronic components of the spectrometer are developed on the basis of a modern element base using programmable logic matrices and microprocessors. Adjustable spectrometric paths and high-voltage power supplies of the PMU are integrated into detection units, modulator driver modules and multi-channel storage are made in the ISA standard and are located in the processor unit of the computer. Setting and monitoring of all parameters of the spectrometer and processing of the measured spectra is carried out from the operating windows of the control and processing programs. Since 2000, more than ten spectrometers of this type have been supplied to leading scientific organizations in Russia and neighboring countries. One of the few industrial applications of Mössbauer spectroscopy should be noted - the development and supply to the Volgodonsk NPP of certified MS-1104Em methods and spectrometer for monitoring corrosion processes in the heat exchange circuits of the VVER-1000 reactor.

An oxygen adsorption station for refueling cylinders is a set of special equipment designed for the production and subsequent refueling of oxygen into cylinders or monoblocks obtained from atmospheric air by short—cycle non-heating adsorption. Unlike the installation, the station is equipped with an oil-free booster compressor, which creates the necessary pressure. Put the squeeze on the compressor. Provita's adsorption stations allow producing oxygen with a purity of up to 99.0%. As a rule, the filling of production gas into cylinders is carried out up to a pressure of 150-200 bar. Composition: 1. Air compressor 2. Dehumidifier 3. Main filter block 4. Air receiver 5. Oxygen generator 6. Oxygen receiver 7. Oil-free booster compressor putting the squeeze on 8.Gas filling ramp

Detection of SCR in all possible range of its characteristics High reliability Self-monitoring of components Backup power supply Recording and storage of measurement results in the non-volatile memory of the device The possibility of integration with external security systems DRG-AT2331 together with SRK-AT2327, personal computer and software "SARK.NET " allows you to form an alarm system for detecting the occurrence of a self-sustaining chain reaction (SAS SCR).

The LOIP LT-117a modification device consists of an immersion thermostat-circulator LOIP LT-100 and a working bath with a flat removable lid. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +100 with tap water cooling °C Tvods+5 ...+100 Accuracy of temperature maintenance, °C ± 0.1 The error of setting the set temperature, no more than ° C ± 0.2 Heater power, W 1900 Pump: max. flow rate, l/min 7.5 pressure, 0.17 bar Bath volume, l 17 The working fluid is water, water-glycerin mixture. Open part of the bath / depth, mm 360x296/150 Overall dimensions, mm 535x335x370 Weight, kg 13

ITAN pH meter/ionometer is a representative of a new generation of universal laboratory pH meters/ionometers with a touch control panel and unique functionality. A magnetic stirrer and a tripod with a foot for installing electrodes and a thermal sensor are built into the pH meter/ionometer housing.

Tube-type thermostats and accessories for laboratory reactor installations complete with a tripod. technical specifications The operating temperature range of the thermostat is 30÷650 °C. The relative accuracy of maintaining the temperature of the thermostat is ± 0.1 ° C. The presence of an indication of the temperature set and maintained in the thermostat. The presence of a thermocouple for temperature control inside the reactor with temperature indication. The diameter and length of the tubular furnace are agreed upon when ordering. The material of the heated part of the tubular furnace (ceramic or stainless steel) is agreed upon when ordering. The height and diameter of the rack (25 or 50 mm) of the thermostat tripod are agreed upon when ordering. The height of the thermostat relative to the base is adjusted by moving on a tripod. The thermostat rotates 360° with locking for operation at any angle from vertical to horizontal. Temperature maintenance modes are isothermal or with temperature programming (multi-stage). A variant of the thermostat is proposed, consisting of two parts that open in the form of a book, each of which has its own thermostat. A variant of the thermostat with multi-zone (along the axis of the thermostat) heating and separate temperature control of each zone is proposed. A variant of a thermostat with control (control) by a personal computer (interface by agreement) is proposed. Reactors for any pressure made of steel 12X18N10T, hasteloy, titanium are offered. Condensers (refrigerators) of the product with any cooling are offered, including on "Peltier" elements. Thermostatic mixers of any type are offered for the reactor plant. Liquid pumps and gas flow shapers are offered for any expenses, gases and pressures.

The characteristics of the device are similar to the GVCH-12A model. The difference is the generator capacity of 25 liters / hour, the purity of the produced hydrogen is lower (99.9995% vol). Technical specifications Purity of hydrogen in terms of dry gas шы about 99.9995% Concentration of water vapor at 20OC and 3 atm is no more than 7 ppm Total hydrogen capacity reduced to normal conditions is 25 l/h The range of the specified output pressure of hydrogen is from 3.0 to 6.1 ati Stability of the output pressure of hydrogen is not worse than ± 0.02 ati The time of setting the operating mode, with the output turned off is no more than 30 min Volume of distilled water to be poured is 1.0 l Distilled water consumption is no more than 0.04 l/h Water consumption is 1.6 g/l of hydrogen The average life of a replaceable deionization filter cartridge (at maximum performance and single-shift operation) is at least 0.5 years Average pump life (for single-shift operation) is at least 0.5 years Power consumption: in stationary mode is no more than 250 VA maximum (at startup) is no more than 280 VA Overall dimensions of the generator, (width x depth x height) is not more than 230x470x450 mm The mass of the generator is. not more than 18 kg Operating conditions: ambient temperature, °C, from +10 to +35 powered by single-phase AC voltage, V, 220 (+10 -15)% and frequency, Hz, 50 +1 The generator for electrical safety meets the requirements of Class 1, type H according to GOST 12.2.025-76

Designed for: use as the primary reference of the spectral power of the noise radio emission SPMSH in the frequency range 140-220 GHz; use as a source of noise signal in the mm wavelength range for use with radio equipment; measuring the noise coefficient of receivers, amplifiers, for tuning and adjusting electronic devices.

The LOIP LT-412a modification device consists of an immersion thermostat-circulator LOIP LT-400 and a working bath with a flat removable lid. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +200 with tap water cooling °C Tvods+5 ...+200 Accuracy of temperature maintenance, °C ± 0.01 The error of setting the set temperature, no more, °C ±0.02 Heater power, W 2200 Pump: max. flow rate, l/min 6...12 pressure, 0.4 bar Bath volume, l 12 The working fluid is water, silicone oil. The open part of the bath / depth, mm 190x296/150 Overall dimensions, mm 355x335x350 Weight, kg 11.8