NV LAB

The Korsa NV-1800 SHVD-U laboratory fume cupboard is a two—frame cabinet with a ceramic granite countertop 1800 mm wide and a small built-in polypropylene sink. This is the largest cabinet with plumbing fixtures in the "NV" line. External dimensions of the cabinet (W×D×H): 1800×700×1960 mm. Dimensions of the working area (W×D×H): 1768×540×750 mm. Table top: granite tiles. Convenient fume cupboards for comfortable work in the laboratory The cabinet is available in two versions: with a hood from the lower cabinet and without it. In a cabinet with such a hood, various aggressive reagents can be stored, in a cabinet without a hood, it is recommended to store only laboratory glass or instruments. Working surface material: porcelain tile. It is moisture-resistant and perfectly withstands high temperatures. It is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. It has limited resistance to hydrofluoric acid. This is one of the most popular types of countertops for laboratory furniture. A small sink-drain is made of polypropylene resistant to aggressive chemicals. Its diameter is 135 mm and its depth is 110 mm. The working area is closed by two independent lifting frames with counterweights. As standard, there are two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. A version with an additional hood from the lower cabinet is also available. Working area size (W×D×H): 1768×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, when the glass is raised, the height of the cabinet will be 2470 mm. The NV-1800 SHVD-U fume cupboard is equipped with a fluorescent lamp with a switch and two sockets, one of them with grounding. Sockets have the IP20 degree of protection, the maximum load on them: 1.5 kW. The basis of the working chamber is an all-welded metal frame in powder coating. Load-bearing laminated panels (chipboard with a thickness of 16 mm) are edged on the facade with a durable PVC edge with a thickness of 2 mm, which increases the impact resistance and mechanical strength of the products. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

Laboratory fume hood Kors NV-1200 SHV-SPB is a single—frame cabinet with a width of 1100 mm with a countertop made of chemically resistant plastic. External dimensions of the cabinet (W×D×H): 1100×700×1960 mm. Dimensions of the working area (W×D×H): 1068×540×750 mm. Table top: chemically resistant plastic. Reliable fume cupboard for laboratories Working surface material: chemical resistant plastic. It is moisture-resistant, resistant to prolonged exposure to concentrated acids and alkalis. It has a limited resistance to high temperature and to prolonged exposure to organic solvents. It is often chosen for laboratories and is suitable for training workshops, analytical and medical laboratories. Ovens or drying cabinets should not be placed on such a countertop. The working area is closed by a single lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1068×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, with the glass raised, the total height of the cabinet will be 2470 mm. The working area is illuminated by an LED lamp (included in the package). The switch is located on the right side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets have thee IP20 degree of protection, maximum load: 1.5 kW. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard with a thickness of 16 mm) are edged with a durable PVC edge with a thickness of 2 mm, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor. What are the other options? There are larger cabinets with a countertop made of chemical-resistant plastic: NV-1500 SHV-SPB, NV-1500 SHVD-SPB and NV-1800 SHVD-SPB.

THe Kors NV-1250 SHV-BC laboratory fume cupboard is a single—frame cabinet with a width of 1240 mm and with a table top made of monolithic ceramics. External dimensions of the cabinet (W×D×H): 1240×700×1960 mm. Dimensions of the working area (W×D×H): 1208×660×1072 mm. Table top: monolithic ceramic. Convenient fume cupboard for comfortable work in the laboratory The table top made of monolithic ceramics is moisture-resistant, perfectly withstands high temperatures. Due to the lack of seams, ceramic granite tiles are better resistant to chemicals and heat. It is possible to place high-temperature equipment on it. The working area is closed by a single lifting frame with a counterweight. There are two exhaust zones in it: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1208×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm it will be 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, when the glass is raised, the height of the cabinet will be 2470 mm. The working area is illuminated by a fluorescent lamp (included in the package). The switch is located on the right side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets have the IP20 degree of protection, maximum load: 1.5 kW. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard 16 mm thick) are edged on the facade with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor. And if we need a cabinet for muffle furnaces? If you need a cabinet to accommodate high-temperature equipment, you might be interested in the ballscrew models. The depth of the countertop is specially increased so that you can put an oven or a cabinet.

The NV-800 NSHS wall cabinet with glass doors is designed for storing devices and materials in the laboratory. The cabinet is equipped with an insert shelf and glass doors. Included in the set: -2 hinged glass doors; -1 shelf-insert; -metal hanging brackets for mounting to the wall.

The NV-1200 SP is a relatively small and inexpensive desk with a countertop width of 1200 mm. It is designed for routine office work in the laboratory. The height of the table is 75 cm (like a regular office desk). The whole table is made of laminated chipboard (chipboard 16 mm thick) and edged on the facade with a 2 mm PVC edge, which increases its impact resistance and mechanical strength. In the right-hand side of the cabinet there are three drawers for storing papers, office and other necessary small stuff. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor. Dimensions of the table when assembled (W×D×H): 1200×600×750 mm. Advantages of NV-1200 SP tables An inexpensive solution for laboratories that value the reliability and durability of furniture; Suitable for very small rooms; It is convenient to work while sitting: the height of the work surface is 75 cm (the height of an average office desk). Application of NV-1200 SP tables Tables of the NV series are used in laboratories of the widest profile: at food and light industry enterprises, in scientific and educational workshops, in chemistry classrooms, quality control centers, medical organizations and many others.

The NV-800 SCm is a specialized laboratory table with a damping concrete slab on a sand cushion. Designed to accommodate centrifuges, sieves and other devices that vibrate strongly during operation. Dimensions when assembled: 860×750×750 mm. The table has a reinforced metal frame. The main countertop has a built-in drawer open from above, which contains a sand cushion. It is closed with a heavy concrete slab attached to a second, smaller countertop. The sand cushion and the concrete base of the second countertop provide good protection against vibrations. The size of the anti-vibration countertop: 550×660 mm. Like the main countertop, it is made of chipboard, and visually they do not differ from each other. The tables have a metal frame painted with powder paint. The side laminated panels (chipboard with a thickness of 16 mm) are edged with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor.

NV-1500 O is an island table with a superstructure that can be placed in the center of the laboratory and organize workplaces on its two sides. Table top depth: 152 cm. It is designed for standing work: the height from the floor to the table top is 85 cm. A lamp and two sockets are built into the superstructure on each side. External dimensions of the table (W×D×H): 1520×1520×1650 mm. Work surface for your tasks We offer tables with various work surfaces. Table Model: Tabletop NV-1500 OL: Laminate. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents. This countertop does not tolerate strong heating or prolonged exposure to solvents, concentrated acids and alkalis. NV-1500 OK: Porcelain tile. It is a practical solution for most chemical, biological, medical laboratories and workshops. You can put drying cabinets, baths and other heating devices on it. NV-1500 OSB: Chemically resistant plastic. It is a good choice for training workshops, analytical and medical laboratories. It does not tolerate high temperatures well, heating devices should not be placed on the surface. NV-1500 OP: Polypropylene. It is chemically resistant, being a specialized solution for chemical laboratories that work a lot with concentrated inorganic acids and alkalis. It is not resistant to high temperatures. A table for convenient work in the laboratory The superstructure allows you to compactly place the necessary reagents and laboratory utensils next to the workplace. Its depth is 30 cm, and its height is 80 cm. The working area on each side is illuminated by a fluorescent lamp (included in the package). The switch is located on the left-hand side of the superstructure. There are also two sockets, one of which is grounded. Sockets (with two on each side, there are four of them in total) have the IP20 degree of protection, maximum load: 1.5 kW. Two cabinets are built into the table on each side, one with a hinged door and a shelf inside, the other with three pull-out drawers. You can store there laboratory utensils or small stuss you need at hand. The side laminated panels of the table (chipboard 16 mm thick) are edged on the facade with a 2 mm PVC edge, which increases their impact resistance and mechanical strength. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor.

The NV-1500 SP is a large inexpensive desk with a tabletop width of 1500 mm. It is designed for routine office work in the laboratory. The height of the table is 75 cm (like that of a regular office desk). The whole desk is made of laminated chipboard (chipboard 16 mm thick) and edged on the facade with a 2 mm PVC edge, which increases its impact resistance and mechanical strength. In the right-hand side cabinet there are three drawers for storing papers, office and other necessary trifles, and in the left-hand side behind the swing door there is one removable shelf. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor. Dimensions of the table when assembled (W×D ×H): 1500×600×750 mm. Advantages of NV-1500 SP tables An inexpensive solution for laboratories that value the reliability and durability of furniture; A wide desk on which you can spread out all the papers; It is convenient to work while sitting: the height of the work surface is 75 cm, like that of a regular office desk. Application of NV-1500 SP desks Tables of the NV series are used in laboratories of the widest profile: at food and light industry enterprises, in scientific and educational workshops, in chemistry classrooms, quality control centers, medical organizations and many others.

The cabinet is made of laminated chipboard with a 2 mm shockproof PVC edge on the facade. The standard equipment of the NV-800 SB includes: 2 doors; chain mount for 2 cylinders.

NV-1200 SHV-M is the most low-budget exhaust cupboard of the NV line. It is single-frame, with a laminated countertop. It is intended mainly for analytical laboratories. External dimensions of the cabinet (W×D×H): 1100×700×1960 mm. Dimensions of the working area (W×D×H): 1068×540×750 mm. Table top: laminated chipboard. A minimalistic solution for your laboratory The NV-1200 SHV-M fume cupboard has a minimum of functions, which makes it the most inexpensive. The table top is made of laminated chipboard. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents. This countertop does not tolerate strong heating or prolonged exposure to solvents, concentrated acids and alkalis. The working area is closed by one lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1068×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, and at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, with the glass raised, the total height of the cabinet will be 2470 mm. The working area is illuminated by a fluorescent lamp (included in the package). The switch is located on the right side of the cabinet body. The base of the cabinet is made on an all-welded metal frame in powder coating. The side laminated panels (chipboard 16 mm thick) are edged on the facade with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a fairly uneven floor. And what are the other options? In the line of NV-1200 cabinets there is a cabinet with plumbing and a surface made of granite tiles, as well as cabinets without plumbing, and with a surface made of monolithic ceramics, stainless steel, chemically resistant plastic. They are exactly the same size as the NV-1200 SHV-M. If you need a minimalistic cabinet of large sizes, you could be interesteed in the NV-1500 SHV-M model.

NV-1500 OH is an island table with a superstructure that can be placed in the center of the laboratory and organize workplaces on both sides. Table top depth: 152 cm. It is designed for standing work: the height from the floor to the table top is 85 cm. A lamp and two sockets are built into the superstructure on each side. External dimensions of the table (W×D×H): 1520×1520×1650 mm. Work surface for your tasks We offer tables with various work surfaces. Table Model: Tabletop NV-1500 OLH: Laminate. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents. This countertop does not tolerate strong heating or prolonged exposure to solvents, concentrated acids and alkalis. NV-1500 OKH: Porcelain tile. It is a practical solution for most chemical, biological, medical laboratories and workshops. You can put drying cabinets, baths and other heating devices on it. NV-1500 OSPH: Chemically resistant plastic. It is a good choice for training workshops, analytical and medical laboratories. It does not tolerate high temperatures well, heating devices should not be placed on the surface. NV-1500 OPX: Polypropylene. It is chemically resistant, being a specialized solution for chemical laboratories that work a lot with concentrated inorganic acids and alkalis. It is not resistant to high temperatures. A table for convenient work in the laboratory The superstructure allows you to compactly place the necessary reagents and laboratory utensils next to the workplace. Its depth is 30 cm, and its height is 80 cm. This table has plumbing fixtures: a faucet and a small sink-drain made of polypropylene resistant to aggressive chemicals built into the countertop. Its diameter is 135 mm and its depth is 110 mm. The working area on each side is illuminated by a fluorescent lamp (included in the package). The switch is located on the left-hand side of the superstructure. There are also two sockets, one of which is grounded. The sockets (with two on each side, there are four of them in total) have the IP20 degree of protection, maximum load: 1.5 kW. Two cabinets are built into the table on each side, one with a hinged door and a shelf inside, the other with three pull-out drawers. You can store there laboratory utensils or small things you need at hand. The side laminated panels of the table (chipboard 16 mm thick) are edged on the facade with a 2 mm PVC edge, which increases their impact resistance and mechanical strength. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor.

The NV-1400 T is a specialized wall—mounted table with a superstructure in which five racks for titration burettes are built. These tables are designed primarily for analytical or training laboratories with a large number of routine manual titration operations. External dimensions of the table (W×D×H): 1400×700×1650 mm. It is designed for standing work: the height from the floor to the countertop is 85 cm. Work surface for your tasks We offer tables with various work surfaces. Table Model: Tabletop The NV-1400 TL: Laminate. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents. This countertop does not tolerate strong heating or prolonged exposure to solvents, concentrated acids and alkalis. The NV-1400 TK: Porcelain tile. A practical solution for most chemical, biological, medical laboratories and workshops. You can put on it drying cabinets, baths and other heating devices. The NV-1400 TSP: chemically resistant plastic. It is a good choice for training workshops, analytical and medical laboratories. It does not tolerate high temperatures well, heating devices should not be placed on the surface. The NV-1400 TP: Polypropylene. It is chemically resistant, neing a specialized solution for chemical laboratories that work a lot with concentrated inorganic acids and alkalis. It is not resistant to high temperatures. A white light-transmitting screen with backlight is built into the superstructure behind the burette racks. It makes the lighting of the work area soft and diffused, convenient for long work. The switch is located on the right-hand side of the superstructure. There are also two sockets, one of which is grounded. Sockets have the IP20 degree of protection, maximum load: 1.5 kW. The tables have a metal frame painted with durable powder paint. The side laminated panels (chipboard 16 mm thick) are edged with a PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The table legs are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor.