TEKHNO-AS

Smart submersible reinforced probe L = 500 mm SZPGU.500P with built-in flash memory is designed to measure the temperature of various materials directly contacting the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor, Android program installed. Operating conditions of the SZPGU.500P smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the SZPGU.500P smart probe Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect external power. Possibility of calibration.

The submersible smart probe L=150 mm SZPG.150 is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor, Android program installed. Operating conditions of the SZPG.150 smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the SZPG.150 smart probe Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

The surfaCE SMART probe L=150 mm SZPV.150 is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor based on the Android program. Operating conditions of the SZPV.150 smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the SZPV.150 smart probe Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor based on the Android program. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor based on the Android program. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

A trace searcher kit for finding underground utilities (cable lines, metal pipelines, and other communications made of conductive materials), as well as the ability to search for places of damage to the external insulation of communications. As part of the kit, the receiver is in the form of a monoblock with a large LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line. Built-in GPS\GLONASS module for determining and recording the coordinates of the location of communication. "Probe" mode for tracing NON-METALLIC communications using an in-tube generator (optional). The most powerful multi-frequency generator with a range of up to 10 km. Connection to the desired route is possible both by contact and contactless method.

For primary and periodic verification and calibration at the field of operation of the following measuring instruments that are part of automated information and measurement systems for commercial accounting of electrical energy (AIIS KUE) or non-automated metering units: • – Measuring voltage transformers (TN) of accuracy classes 0.2 and less accurate at loads normalized by GOST, and at real loads at the metering unit. • – Measuring current transformers (TT) of accuracy classes 0.2S and less accurate with nominal primary currents of 100...5000 A (including high-voltage transformers for 330 kV lines) at loads standardized by GOST 7746-2001 and at real loads; single-phase and three-phase electric active and reactive energy meters of accuracy classes 0.2S and less accurate. • – Auxiliary SI: ammeters, voltmeters, wattmeters, voltage, current and power converters, accuracy classes 0.2 and less accurate, phase meters, power factor meters of accuracy classes from 0.10 and less accurate. • – Energy frequency meters of accuracy classes from 0.02 and less accurate, used at the electricity metering unit. • – For measuring the load capacity of TN iTT. • – For measuring voltage losses in secondary TN circuits. – For measuring the quality of electrical energy (PCE) in accordance with the requirements of GOST 13109-97.

The set is correlational-acoustic with two radio channels, the ability to trace metal and non-metallic pipelines (by acoustic method and in the "Probe" mode) with the function of saving GPS/GLONASS coordinates and the function of diagnosing shut-off valves. Designed for: – determination of the location of liquid leakages from pipelines by the correlation method; – tracing underground utilities; • – tracing of non–metallic pipelines by acoustic method and in the "Probe" mode; - clarification of leakage sites by acoustic leak detector; – diagnostics of shut-off valves; – search for damage to cable lines by induction and acoustic (together with GVI) methods; – creation of an information database on the condition of pipelines and the results of pipeline diagnostics.

A trace searching kit for searching underground utilities (cable lines, metal pipelines, and other communications made of conductive materials). The kit includes a receiver in the form of a monoblock with a large LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line and the most powerful multi-frequency generator in the TECHNO-AC line, with a range of up to 10 km.

The set is correlational-acoustic with two radio channels, the ability to trace metal and non-metallic pipelines (by acoustic method and in the "Probe" mode) with the function of saving GPS/GLONASS coordinates and the function of diagnosing shut-off valves. Designed for: – determining the location of liquid leakages from pipelines by the correlation method; – tracing underground utilities; • – tracing of non–metallic pipelines by acoustic method and in the "Probe" mode; - clarification of leakage sites by acoustic leak detector; – diagnostics of shut-off valves; – search for damage to cable lines by induction and acoustic (together with GVI) methods; – creation of an information database of the condition of pipelines and the results of pipeline diagnostics.

The electronic thermometer TK-5.01S is designed to measure the temperature of liquid, bulk materials by direct contact of the probe with the measuring object. The electronic thermometer consists of an electronic unit and a non-replaceable submersible probe. Thermoelectric converters (TP) with NSH according to GOST R 8.585 are used as a thermosensitive element in the probe. •

A frost-resistant kit with a powerful generator that solves problems on metal and non-metallic pipelines designed for: • – search for underground utilities (power and signal cable lines, reinforced fiber-optic lines, pipelines made of electrically conductive materials), as well as determining the depth of their occurrence and places of damage. • – determination of the location of power cable lines by induction and acoustic methods. • – high-range tracing and highly efficient search for cable damage sites. • – tracing of non-metallic and metallic pipelines by acoustic method and search for leaks from pipelines.

Purpose of the thermometer TK-5.04S The digital contact thermometer TK-5.04S is designed to measure the temperature of various materials by direct contact of the probe with the measuring object. The digital contact thermometer consists of an electronic unit and replaceable probes. Thermoelectric converters (TP) with NSH according to GOST R 8.585 are used as thermosensitive elements in the probes. •

High-temperature smart surface probe L=300 mm SZPVV.The 300P with built-in flash memory is designed to measure the temperature of various materials by directly contacting the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor, Android program installed. Operating conditions of the SZPVV smart probe.300P Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the SZPVV smart probe.300P Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.