Equipment

The generators are designed to supply analytically clean air to flame ionization detectors and gas analyzers. They are available in two versions depending on performance and output pressure. Thanks to the presence of a system of catalytic purification of air from hydrocarbons, the generator can significantly improve the accuracy and sensitivity of chromatographic analyses. Technical specifications Air capacity reduced to normal conditions is not less than 1.2 l/min Outlet air pressure is 355 ± 5% kPa(3.5 ati) Output pressure stability at constant flow rate is not worse than ± 5 kPa Stability of the output pressure when the flow rate changes from 0.3 l/min to the maximum value is not worse than ± 7 kPa Output concentration of hydrocarbons is not more than 0.1 ppm The concentration of water vapor at 20°C and 100kPa, is no more than 10 ppm Ready time after switching on is no more than 30 min Power consumption is not more than 150 VA Overall dimensions of the generator (width x depth x height) are not more than 230x470x450 mm The mass of the generator is not more than 15 kg Working conditions: ambient temperature, °C from +10 to +35 relative humidity of the ambient air, % 80 power supply from a single-phase network: AC voltage, 220 ± 10% and frequency, Hz 50 ± 1

Design features: Special system of air intake and exhaust of combustion products with adjustable thrust; Durable ceramic muffle; Closed heaters on four sides of the chamber; Microprocessor temperature controller; Conveniently located control panel and bright LED display; Ease of management and control; LED indicators of heater operation and protection operation; Automatic shutdown of heating when opening the door; The door opens up and faces the user with the cold side; Alarm when the current temperature exceeds the limits of the permissible range; Highly efficient thermal insulation of the housing; The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint. Technical specifications: Maximum heating temperature, °C +1100 Temperature stability in steady-state thermal mode, °C ± 10 Warm-up time to the maximum temperature, no more than 120 min Dimensions of the working chamber, WxHxD, not less than 200x150x290 mm Overall dimensions, WxHxD, not more than 525x1015x620 mm Rated supply voltage, 220 V Rated power, W 5500

Technical specifications: Temperature range: without external cooling, °C Current+10 ... +100 with tap water cooling °C Tvods+5 ...+100 Accuracy of temperature maintenance, °C ± 0.1 The error of setting the set temperature, no more than ° C ± 0.2 Heater power, W 1900 Pump: max. flow rate, l/min 7.5 pressure, 0.17 bar Bath volume, l 11 The working fluid is water, water-glycerin mixture. The open part of the bath / depth, mm 160x240/200 Overall dimensions, mm 330x270x370 Weight, kg 4,8

The vacuum trap of the condenser type FVC-2/20-X in a chemically resistant design with a capacity of 2 liters is designed to condense aggressive gas vapors on the internal cooled surfaces of the trap, in order to prevent them from entering the pump.

A membrane nitrogen station is a set of equipment for the production and supply of nitrogen under high pressure obtained from atmospheric air by the method of membrane separation. Unlike the membrane nitrogen plant, the membrane nitrogen station is equipped with additional equipment: a booster compressor that creates the necessary pressure. Put the squeeze on the pump. Composition of a typical membrane nitrogen station: 1. Air compressor 2. Dehumidifier 3. Main filter block, including coal column 4. Air receiver 5. Membrane nitrogen generator 6. Nitrogen receiver 7. Nitrogen booster compressor putting the squeeze on

Technical specifications: Operating temperature range, °C -25...+100 Accuracy of temperature maintenance, °C ± 0.1 The discreteness of the temperature display, ° C 0.1 Cooling capacity at 20 °C, W 650 Pump capacity in the discharge (suction) circuit, not less than, l/min 8 Volume of working fluid, l 16 Power supply, V/Hz 220/50 Power consumption, not more than 3.6 kW Open part of the bath/depth, mm 248x170/200 Overall dimensions, mm 450x420x890 Weight without working fluid, kg 55

Designed for collecting, storing and distributing purified water obtained by various purification methods, with a capacity of 60 liters and 100% stainless steel, which allowed for a long service life. Dimensions in terms of 450x500 mm Weight 8.1 kg

A specialized muffle, combined with an enlarged heating plate, for carrying out the sample preparation process under optimal conditions when programming the operating mode. Operating temperature range: salting chamber, oS - from 200 to 750 working surface of the evaporation chamber, oS - from 70 to 400

Multifunctional trace searching kit for finding underground utilities (cable lines, metal pipelines and other communications made of conductive materials). The presence of an acoustic sensor and a shock mechanism allows tracing NON-METALLIC pipelines, as well as searching for leaks from pipelines and searching for cable damage sites. The isolation monitoring sensors DKI-117 and the sensor-detector of communication defects DODK-117 search for places of damage to the external insulation of communication. The kit includes the most powerful multi-frequency generator with a range of up to 10 km. Connection to the desired route is possible both by contact and contactless method.

The fan body and impeller are made of polypropylene, which has a very high chemical resistance, especially to concentrated inorganic acids and their vapors. The design rules out the contact of the transported air with any parts that are prone to corrosion. 1.Autonomous acid-resistant fan 1200 cubic meters per hour Width - 570 POLYPROPYLENE - 48 620 ₽ 2.Autonomous acid-resistant fan 1200 cubic meters per hour (with a frame for wall mounting) Width - 570 POLYPROPYLENE - 52 520 ₽ 3.Autonomous acid-resistant fan 1700 cubic meters per hour Width - 664 POLYPROPYLENE- 52 940 ₽ 4.Autonomous acid-resistant fan 1700 cubic meters per hour (with a frame for wall mounting) Width - 664 POLYPROPYLENE - 56 840 ₽

Allows to significantly simplify the procedure for checking, configuring and demonstrating microprocessor relay protection units. The use of the stand makes it possible to significantly simplify the procedure of demonstration, verification and configuration of microprocessor relay protection units. The stand allows to check such protections as MTZ and OZZ, including directional, ZMN, ZPN, ZOF. With the help of the stand, you can easily check the automation functions of the RZA units, for example, URV, APV, AVR, etc.