Equipment

The gas distribution panel (hereinafter referred to as the panel) is designed to connect gas nodes and blocks of various analytical instruments, including chromatographs to shop gas lines. technical specifications Inlet pressure, not more than 0.8 MPa. The output pressure is from 0 to 0.4 MPa. Gas flow rate through each channel, not less than — 1000 cm3/min.

Laboratory equipment for 0.4-35 kV cable lines (ETL-35) 1. Test facility • – Maximum rectified voltage up to 70 kV; • – Maximum AC voltage of the industrial frequency of 50 Hz to 100 kV. 2. Burning facility • – Maximum voltage up to 30 kV; • – Maximum current up to 80 A; • – Working hours are not limited; • – Switching of stages is carried out without breaking the arc at the time of switching; • – The ability to start working from any stage of burning (when working with low-voltage cables); • – Built-in afterburning. 3. High voltage pulse generator • – Output voltage 0...12 kV / 0...24 kV; • – The pulse energy at each stage is 3000 J; • – Built-in IDM for collaboration with the reflectometer. 4. Reflectometer – Supports 3 methods of determining the location of damage: • – By pulse reflectometry; • – By the method of oscillatory discharge; • – Pulse-arc method. 5. High-voltage cable defects detector • – Determining the location and depth of the cable at a depth of up to 10 m; • – Tracing at a distance of up to 10 km; • – Search for live electrical cables; • – Search for places where the pipeline and cable intersect; • – Determining the places of damage to cable lines; • – Site surveys before excavation; • – Search for places of damage to the external insulation of the cable; • – GPS\GLONASS coordinates recording and mapping of found communications; • – Cable selection from the bundle; • – Search for the place of damage by acoustic method.

It is intended for thermostating samples in glasses, flasks and other laboratory utensils in cases where high accuracy of temperature maintenance is not required and good uniformity of the temperature field in the working volume is not needed. The operating temperature range is +5...+200 °C. Six workstations with a diameter of 110 mm with five steel O-rings, tripods and feet with a clip. Stamped steel tub with a volume of 25 liters and a depth of 160 mm. The volume of the bath is 25 liters Overall dimensions 570x660x710 mm The open part of the bath is 500x290 mm Bath depth 160 mm Weight 16 kg Power consumption 2.5 kW

The laboratory drying cabinet SNOL-F-67 is designed for thermal testing, aging, as well as drying, tempering and other types of heat treatment of various materials in an air environment at temperatures up to 500 ° C with natural or forced air convection in stationary conditions.

Technical specifications: Ambient temperature, °C from +10 to +35 Relative humidity (at +25 °C), % no more than 98 Atmospheric pressure, kPa from 84 to 106.7 Power supply 220  22 V, 50  1 Hz Power consumption, VA no more than 150 Overall dimensions (LWC), mm Monitor Multiplexer 665x482x222 665x482x222 Weight, kg Monitor Multiplexer (2-16 channels) 25 15 - 25 Average time to failure, h 12000 Average service life, 5 years

The Athlete AG-324 cable searcher is a combination of the modern American Ridgid SR-24 track finder receiver and the most powerful multi-frequency portable generator AG-120T in the line of TECHNO-AC generators.

Designed for: – determining the location of leakages from pipelines by the correlation method; – tracing underground utilities; – clarification of the leak location by an acoustic leak detector; – creation of an information database on the condition of pipelines and the results of pipeline diagnostics; – search for the place of damage to the power cable by induction and acoustic methods.

Design features: Microprocessor temperature controller; Four-sided heating; Shut-off forced air circulation in the working chamber; The material of the chamber is steel painted with heat–resistant paint; Bright LED display; Conveniently located control panel; LED indicators of heater operation and protection operation; Alarm when the current temperature exceeds the limits of the permissible range; Reliable door closing mechanism; High-quality silicone sealer; Highly efficient thermal insulation of the housing; The case is made of high-quality sheet steel and painted with heat-resistant powder paint; Number of shelves: standard – 2, maximum – 6. Technical specifications: Maximum heating temperature, °C +350 The error of reproducing the set temperature ° C ± 3 Temperature maintenance error, ° C ± 1 Warm-up time to the maximum temperature, no more, min 45 Dimensions of the working chamber, (WxHxD), not less than mm 340x365x370 Overall dimensions, (WxHxD), not more than 685x580x680 mm Rated supply voltage, 220 V Rated power, W 2200

DPSS lasers of the KLM-457/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes. Technical specifications Radiation output power: up to 10W Radiation wavelength: 457 nm Output beam diameter: 1.5mm Divergence of the radiation beam: 1.3 mrad Instability of radiation power: 5% Type of modulation: TTL or analog Time to enter the mode: 15min Spectral line width: 0.1nm

Type of motion reciprocating The maximum oscillation frequency of the platform, min-1 250 The amplitude of the platform movement, mm 10 Maximum load on the platform, kg 2 Power consumption, W 50 Platform size, mm 315x210 Overall dimensions, mm 360x310x170 Weight, kg 9

Devices capable of generating oxygen have found the widest application in various fields of medicine. The equipment is also used in training centers, educational institutions and oxygen rooms. Medical oxygen concentrators allow to accelerate the recovery of patients suffering from cardiovascular diseases, chronic respiratory diseases, as well as other pathologies that make it difficult to saturate the blood with oxygen. This equipment is a mandatory equipment for anesthesiology and intensive care units. Oxygen concentrators demonstrate high efficiency in restorative treatment. Unlike oxygen sources, which use compressed gas, generators are characterized by high safety and efficiency Capacity: 200 l/min 12 m3/h 16 kg/hour Oxygen purity: 95 % Oxygen pressure: 4-5 bar

The OptoTL-60/125 interferometer by Opto-TL is designed for non-contact technological control of the shape accuracy (N/ΔN) of optical polished flat and spherical surfaces with a diameter of up to 125 mm, measuring their radii, and also for checking the distortion of lens wavefronts. Characteristic features of the interferometer OptoTL-60/125: • small dimensions for placement in production next to optical machines; • specially developed original FastInterf software for operational measurements in production conditions; • original ruler calibration program for measuring radii; • the presence of two monitors for quick adjustment and visualization of the interference pattern; • New! the presence of two light sources (coherent and non-coherent) to reduce the influence of reflection of the second side when testing plane-parallel plates (option); • motorized fast vertical movement by servomotor; • motorized precise vertical movement using a pulse generator with a sensitivity of 30 nm; • New!automatic vertical movement by a specified amount (from the «cat's eye» position to the confocal position and vice versa) (option); • two standard sizes of reference lenses 60 mm and 125 mm with adapter 60/125; • adjusting table for tilting and moving the controlled samples; • the presence of base surfaces for the table and controlled parts to simplify alignment when controlling a batch of identical parts; • device for tilting steep blocks (option); • base and vertical stand made of syntegran for better damping of vibrations; • passive system of vibration isolation sufficient for work in industrial conditions; • The interferometer is delivered on a turnkey basis, complete with everything you need to get it up and running.