Catalog
Back to search results
Tracing generator AG-114.1
Back to search results
Tracing generator AG-114.1
from
94 530 ₽
from
94 530 ₽
Go to the manufacturer's website
The automatic tracing pulse generator AG-114 is designed to create propagating signals (vibrations) in the routes of hidden communications with the active method of tracerouting. The device creates an alternating sinusoidal current in the studied communication (constantly or in short-term parcels) necessary to determine its location.
Features of the AG-114 generator
The selected output power (5 W at 1...1000 ohms, 10 W at 1...500 ohms, 20 W at 1...250 ohms) is issued automatically. The ability to work on such high load resistances allows you to trace very extensive communications. Low power provides energy saving and small "readjustments" to neighboring objects, high power provides a high range of broadcast and detection.
Three generation modes:
pulse – the main high-efficiency mode with high intelligibility against interference;
continuous – an additional low-cost mode for short-term special measurements;
three–frequency mode, which provides the selection of the optimal frequency on a remote receiver without switching the transmitter (generator).
Three generation frequencies: 512 Hz, 1024 Hz, 8928 Hz. Lower frequency – less "readjustment" to neighboring objects, higher frequency – higher detection range.
Unusually compact (190x140x80 mm), for such a high output power (20 W), the autonomous design is provided by the use of highly efficient technology "CLASS D (BD)" (pulsed output power amplifier with an efficiency of 80%). As a result, one small-sized autonomous battery with a capacity of only 2.2 Ah provides pulse generation for >5 hours at maximum output power (20 watts).
It is possible to work with "recharge" from the charger or increase capacity by connecting an external battery to increase the time resource.
The control and display system, which contains only 4 large keyboard switches and 2 LEDs with specific signatures and symbols ("intuitive interface") and is not overloaded with unnecessary, for automatic devices, fine-tuning organs and indicators of numerical parameter values, is designed for convenient operation in the field. The device does not require constant supervision, parameter monitoring, frequent operational switching and is designed to work on the principle of "turned on and went to the track". In case of significant changes in the load resistance (communication) during generation, the device is automatically reconfigured ("repeated auto-negotiation").
Features of the AG-114 generator
The selected output power (5 W at 1...1000 ohms, 10 W at 1...500 ohms, 20 W at 1...250 ohms) is issued automatically. The ability to work on such high load resistances allows you to trace very extensive communications. Low power provides energy saving and small "readjustments" to neighboring objects, high power provides a high range of broadcast and detection.
Three generation modes:
pulse – the main high-efficiency mode with high intelligibility against interference;
continuous – an additional low-cost mode for short-term special measurements;
three–frequency mode, which provides the selection of the optimal frequency on a remote receiver without switching the transmitter (generator).
Three generation frequencies: 512 Hz, 1024 Hz, 8928 Hz. Lower frequency – less "readjustment" to neighboring objects, higher frequency – higher detection range.
Unusually compact (190x140x80 mm), for such a high output power (20 W), the autonomous design is provided by the use of highly efficient technology "CLASS D (BD)" (pulsed output power amplifier with an efficiency of 80%). As a result, one small-sized autonomous battery with a capacity of only 2.2 Ah provides pulse generation for >5 hours at maximum output power (20 watts).
It is possible to work with "recharge" from the charger or increase capacity by connecting an external battery to increase the time resource.
The control and display system, which contains only 4 large keyboard switches and 2 LEDs with specific signatures and symbols ("intuitive interface") and is not overloaded with unnecessary, for automatic devices, fine-tuning organs and indicators of numerical parameter values, is designed for convenient operation in the field. The device does not require constant supervision, parameter monitoring, frequent operational switching and is designed to work on the principle of "turned on and went to the track". In case of significant changes in the load resistance (communication) during generation, the device is automatically reconfigured ("repeated auto-negotiation").
Tracing generator AG-107
from
126 270 ₽
The AG-107 generator is designed to create alternating current in electrically conductive communications with the electromagnetic method of tracerouting.
Features of the AG-107 generator
The main distinguishing feature is the small weight and dimensions of the device with high output power.
The AG-107 generator has a built-in battery based on light high-capacity lithium-iron phosphate (LiFePO4) cells with low self-discharge, dimensions 216x180x105 mm, weight 1.8 kg and provides the following maximum output parameters:
The output power in continuous operation is 30 watts;
output power in intermittent operation mode is 60 W;
Output voltage 60 V;
current 5 A.
The AG-107 generator uses a control interface similar to the AG-105 generator.
The generator implements:
Four sine wave generation frequencies: 512 Hz, 1024 Hz, 8192 Hz and 33 kHz;
continuous, pulse and dual-frequency generation modes;
built-in transmitting antenna operating at frequencies of 8192 Hz and 33 kHz;
the possibility of connecting an external transmitting antenna and induction tongs;
built-in "multimeter" displaying, at the operator's choice, the supply voltage or output parameters: current, power, voltage, load resistance;
the ability to work from an external battery or from the mains ~ 220 V.
The generator can be operated from an external power supply of 10...25 V.
The generator is protected from the effects of voltages up to 400 V when connected to the communication and from exceeding the permissible voltage of the external power supply.
The degree of protection of the case - case IP65 completely eliminates the penetration of dust and water jets inside when the lid is open.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Tracing generator AG-120TM
from
238 050 ₽
The AG-120TM generator is designed for localization and diagnostics of underground utilities (cables, pipelines).
The maximum power of the generator is up to 300 watts (depending on the selected operating mode).
The device has no equal in the qualitative indicator of the ratio: power-resource-dimensions-weight.
Application of the AG-120TM generator
To trace communications by electromagnetic method (cables, metal pipelines) and acoustic method (metal and non-metallic pipelines).
To carry out a highly efficient search for cable damage sites.
Carry out diagnostics of gas pipelines and determine the places of damage to the insulation of protective coatings.
Work with any receiver due to the possibility of selecting any operating frequency in the range of 200-10000 Hz.
Features of the AG-120TM generator
Increased battery capacity compared to the AG-120T generator.
Automatic matching for a given current in the load, instead of the output power, allows you to get the predicted signal level at the input of the search receiver.
The multi-frequency (200-10000 Hz) multifunctional device can be equipped with any search receiver using this frequency range.
Automatic selection of output power by an “intelligent” power selection program.
The built-in “output multimeter” shows the voltage, current, resistance and power in the load.
High output current (up to 15 A) makes it possible to work efficiently on “low-resistance” (up to short-circuit) loads (for example, grounded pipelines).
High output voltage (220 V auto./330 V with complement. battery) allows you to effectively trace “high-resistance” long-range communications.
Multifunctionality: operation without direct connection with a resonant transmitting antenna, inductive pliers, a shock mechanism and an isolation monitoring sensor.
Ability to work in rainy weather (on/off; viewing parameters with the lid closed).
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Tracing generator AG-144.1
from
154 560 ₽
The automatic tracing generator AG-144.1 is designed to create propagating signals in the routes of hidden communications with active methods of tracing (electromagnetic and acoustic). The device creates in the studied communication an alternating sinusoidal current necessary to determine its location or sound pulses using a shock mechanism.
Sinusoidal generation (electromagnetic traceroute method)
The selected power levels are issued automatically and are in offline mode: 7.5 W at 0.1...1300 ohms, 15 W at 0.15...660 ohms, 30 W at 0.3...1300 ohms, 60 W at 0.6...660 ohms - CONTINUOUSLY, or 15 W at 0.15...660 ohms, 30 W at 0.3...330 OHMS, 60 Watts at 0.6... 660 ohms, 120 watts at 1.2... 330 ohms - PULSES. When using an additional 12/24 V external battery (for example, a car), an output power of 45 watts at 0.45...2000 ohms, 90 watts at 0.9...1000 ohms CONTINUOUSLY, or 90 watts at 0.9... 1000 ohms, 180 watts at 1.8...500 ohms – PULSES can be achieved. The ability to work on such high load resistances allows you to trace very extensive communications. Low power provides energy saving and small "readjustments" to neighboring objects, high power provides a high range of broadcast and detection.
Three generation modes:
pulse – a highly economical mode with high intelligibility against the background of interference is good for interfacing with analog (mainly single-sensor) receiving systems;
continuous – mode is required for most multi-sensor digital receiving systems;
three–frequency mode, which provides the selection of the optimal frequency on a remote receiver without switching the frequency of the transmitter (generator).
Three generation frequencies: 512 Hz, 1024 Hz, 8192 Hz. Lower frequency means less "readjustment" to neighboring objects and higher broadcast range, higher frequency means higher receiver sensitivity, but greater signal attenuation in "long" communication.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
A set of an autonomous generator MAG-05.2.XX
from
117 300 ₽
A set of an autonomous generator MAG-05.2.XX is used for tracing and determining the depth of non-metallic pipelines, storm channels at a depth of up to 5 meters in conjunction with tracerouting receivers having a "Probe" function with an operating frequency of 512 Hz.
The principle of tracing non-metallic pipelines with an autonomous MAG-05 generator.2.XX
A small-sized autonomous generator MAG-05 is placed on a problematic section of the highway using a cable pushing device. The generator emits an electromagnetic field.
When the receiver is moved on the earth's surface (when the receiver axis is perpendicular to the communication axis), a signal with pronounced two local minima, a general maximum and two false peaks is induced along the communication axis in the receiving coil. When moving the receiver across the axis of the generator, there are no local minima and false peaks of the signal.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Tracing generator AG-120T
from
238 050 ₽
The AG-120T generator is designed for localization and diagnostics of underground utilities (cables, pipelines).
The maximum power of the generator is from 120 W to 270 W (depending on the selected operating modes).
The device has no equal in the qualitative indicator of the ratio: power-resource-dimensions-weight.
Application of the AG-120T generator
To trace communications by electromagnetic method (cables, metal pipelines) and acoustic method (metal and NON-metallic pipelines).
To perform a highly efficient search for cable damage sites.
To carry out diagnostics of gas pipelines and determine the places of damage to the insulation of protective coatings.
To work with any receiver thanks to the possibility of selecting any operating frequency in the range of 200-10000 Hz.
the features of the AG-120T generator
Automatic matching for a given current in the load, instead of the output power, allows you to get the predicted signal level at the input of the search receiver.
The multi-frequency (200-10000 Hz) multifunctional device can be equipped with any search receiver using this frequency range.
Automatic selection of output power by an “intelligent” power selection program.
The built-in “output multimeter” shows the voltage, current, resistance and power in the load.
High output current (up to 15 A) makes it possible to work efficiently on “low-resistance” (up to short-circuit) loads (for example, grounded pipelines).
High output voltage (220 V auto./330 V with complement. battery) allows you to effectively trace “high-resistance” long-range communications.
Multifunctionality: operation without direct connection with a resonant transmitting antenna, inductive pliers, a shock mechanism and an isolation monitoring sensor.
Ability to work in rainy weather (on/off; viewing parameters with the lid closed).
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Tracing generator AG-105
from
89 400 ₽
The automatic tracing pulse generator AG-105 is designed to create propagating signals (vibrations) in the routes of hidden communications with the active method of tracerouting. The device creates an alternating sinusoidal current in the studied communication (constantly or in short-term parcels) necessary to determine its location.
The features of the AG-105 generator
Extremely high power output and battery life, for a compact battery pack ("Type C" × 8) and such small overall dimensions.
Universal power supply allows you to reach an output power of over 20 watts. With autonomous power supply, the "life cycle" depends on the quality of the "type C" batteries used. For example, with an initial output power of 7 watts in continuous generation mode, the "life cycle" is ≈ 5 hours, and with an initial output power of 15 watts in intermittent modulation mode, the "life cycle" is ≈ 25 hours (using standard new "fresh" batteries, for example, "Energizer C"). When using "ultra-high-capacity" batteries (for example, "Duracell ULTRA" or "COSMOS"), the battery life can be increased by 20-30%. When connecting an external "12V" battery (for example, a car), the operating time is determined by the capacity of this battery. When connecting an external mains power supply "15 V", the operating time is not limited.
The dimensions of the portable device in the case are 216x180x105 mm, and the weight does not exceed 2 kg.
These features are provided by the use of an ultra-efficient unique modification of the circuit technology for building CLASS D power amplifiers. The pulse output amplifier reaches an efficiency of 85%, which is especially important for "energy-consuming" devices with autonomous power supply.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Tracing generator AG-105
from
100 740 ₽
The automatic tracing pulse generator AG-105 is designed to create propagating signals (vibrations) in the routes of hidden communications with the active method of tracerouting. The device creates an alternating sinusoidal current in the studied communication (constantly or in short-term parcels) necessary to determine its location.
The features of the AG-105 generator
Extremely high power output and battery life, for a compact battery pack ("Type C" × 8) and such small overall dimensions.
Universal power supply allows you to reach an output power of over 20 watts. With autonomous power supply, the "life cycle" depends on the quality of the "type C" batteries used. For example, with an initial output power of 7 watts in continuous generation mode, the "life cycle" is ≈ 5 hours, and with an initial output power of 15 watts in intermittent modulation mode, the "life cycle" is ≈ 25 hours (using standard new "fresh" batteries, for example, "Energizer C"). When using "ultra-high-capacity" batteries (for example, "Duracell ULTRA" or "COSMOS"), the battery life can be increased by 20-30%. When connecting an external "12V" battery (for example, a car), the operating time is determined by the capacity of this battery. When connecting an external mains power supply "15 V", the operating time is not limited.
The dimensions of the portable device in the case are 216x180x105 mm, and the weight does not exceed 2 kg.
These features are provided by the use of an ultra-efficient unique modification of the circuit technology for building CLASS D power amplifiers. The pulse output amplifier reaches an efficiency of 85%, which is especially important for "energy-consuming" devices with autonomous power supply.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Trace Searcher Success AG-309.30M (frost-resistant)
from
198 600 ₽
The trace searching kit is designed to accurately determine the location and depth of underground utilities (power and signal cable lines, reinforced fiber-optic lines, pipelines made of electrically conductive materials), troubleshooting cable lines, and also allows you to conduct a survey of the area in the shortest possible time and with great reliability before excavation and to prevent damage to engineering communications.
As part of the kit, the receiver is in the form of a monoblock with a frost-resistant LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line.
The kit is equipped with the latest compact autonomous generator AG-107 with built-in batteries, display and built-in induction antenna, for tracing communication in a contactless way.
The output power of the generator is up to 60 watts.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Trace searcher Success AG-309.15N
from
183 540 ₽
The trace searching kit is designed to accurately determine the location and depth of underground utilities (power and signal cable lines, reinforced fiber-optic lines, pipelines made of electrically conductive materials), troubleshooting cable lines, and also allows you to conduct a survey of the area in the shortest possible time and with great reliability before excavation and to prevent damage to engineering communications.
As part of the kit, the receiver is in the form of a monoblock with a large LCD display, which displays an image of the route and automatically calculates the depth of the communication up to 10 m, as well as the current in the line. Connection to the desired route is possible both by contact and contactless method.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Cable Finder Success KBI-306N
from
75 600 ₽
Description of the cable finder Success KBI-306N
• – Traceroute receiver in the form of a monoblock with LED indication and sound output to the built-in speaker.
• – Automatic calculation and display of the depth of communication up to 10 m.
Purpose of the cable finder Success KBI-306N
• – Search for live electrical cables.
• – Search and tracing of underground utilities (gas pipelines, pipelines, power and telephone cables).
• – Determination of the occurrence of underground utilities at a depth of up to 10 m.
Features of the AP-017N receiver
• – Modern digital traceroute receiver-monoblock.
• – Bright LED indicator.
• – Displays the measured depth value on the screen.
• – Determination of the deviation from the axis of the route by the LED indicator and the sound signal.
• – Wide range of operating frequencies (50 / 100 / 512 / 1024 / 1450 / 8192 / 8928 / 9820 Hz, Wide Band 12...24 kHz).
• – Frost-resistant, working at temperatures up to -40 ° C.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Mobile laboratory NEURONET TECHNOAS 4 based on Gazelle Next
Purpose of the NEURONET TECHNOAS 4 Laboratory
• – Universal educational complex of modern educational technologies;
• – Mobile remote and educational office for the working coherence of the subjects of activity.
The use of the NEURONET TECHNOAS 4 laboratory
• – Hardware and software complex based on multifunctional neuro-modular systems of electroencephalographs-recorders "Encephalan-EEGR-19/26";
• – Improving the productivity and profitability of the work of teams with physio-psychological diagnostics and correction, with machine neuro-training on biofeedback;
• – Biophysical individual adjustment of the central nervous system;
• – Conscious development of new reflexive meaningful states, rapid assimilation of new knowledge, skills, skills and actions;
• – Reduction of dangerous influences of the human factor in responsible professions (aviation and others);
• – Improving the effectiveness of educational programs for special education, retraining and advanced training.
NEURONET TECHNOAS 4 Laboratory Support System
• – MKZ safety control module;
• – Mass switches in all compartments;
• – Smart Home system, continuous monitoring of all life support systems with video recording;
• – Audible alarm;
• – Light alarm;
• – An autonomous power source from batteries with a 12/220 V voltage converter;
• – 12 V - 220 V sockets;
• – Hardware and software complex of neuro-modular systems of electroencephalographs-recorders "Encephalan-EEGR-19/26";
• – Hardware and software complexes of modern educational technologies integrated with the Central Control Unit (central control unit).
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
The meter of complex coefficients of transmission and reflection P4-69
NNPO im. M.V.Frunze
Nizhny Novgorod
Produced in: Nizhny Novgorod
Trace searcher Success AG-528.60N
from
225 630 ₽
The trace searching kit is designed to accurately determine the location and depth of underground utilities (power and signal cable lines, reinforced fiber-optic lines, pipelines made of electrically conductive materials), troubleshooting cable lines, and also allows you to conduct a survey of the area in the shortest possible time and with great reliability before excavation and to prevent damage to engineering communications.
The kit includes a digital multifunctional tracking receiver with a large LCD display and audio output both to the built-in speaker and to the operator's headphones.
The generator has increased power up to 180 watts and a range of up to 5 km. Connection to the desired route is possible both by contact and contactless method.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Power supply C35-80
Operating Mode: Continuous
Output stabilized current, A: 1-80
Output voltage, V: 0-35
Power supply: Three-phase 220/380 V 50 Hz
Operating temperature range, °C: +10...+35
Storage temperature, °C: -20...+45 Relative humidity (without condensation), %: 90 Weight, kg: 5.3
Overall dimensions (W x H x D), mm: 390 x 75 x 200
INZHEKT
Saratov
Produced in: Saratov
Power supply B5-89, B5-89/1
Technical specifications:
Indicator name, unit of measurement, Indicator value,
B5-89, B5-89/1
The range of the output voltage setting, the limits of the absolute error of the output voltage setting:- basic error, In; - in operating conditions, In, from 0 to 30.0 ± 0.2± 0.3, from 0 to 100.0 ± 0.3± 0.45
The range of the output current setting, the limits of the absolute error of the output current setting:- basic error, A; - in operating conditions, A, from 0 to 10.0 ± 0.2± 0.3, from 0 to 3.0 ± 0.1± 0.15
Instability of the output voltage when the supply voltage changes by ± 10% of the nominal value in the voltage stabilization mode, %, ± 0.05, no more,
Instability of the output current when the supply voltage changes by ± 10% of the nominal value in the current stabilization mode, %, ± 0.2, no more,
Instability of the output voltage when the load current changes at the output terminals of power supplies in voltage stabilization mode, %, ± 1, no more,
Instability of the output current when the load voltage changes in the current stabilization mode at minimum load currents, %, ± 5, no more,
Instability of the output current when the load voltage changes in the current stabilization mode at maximum load currents, %, ± 0.5, no more,
Output voltage ripple in voltage stabilization mode, mV, 1.0, no more,
Output current ripple in current stabilization mode, %, 1, no more,
Instability of the output voltage from time, V, ± 0.5, ± 1.0
Instability of the output current from time, A, ± 0.3, ± 0.2
AC power supply: - voltage, V; - frequency, Hz, 230 ± 2350 ± 0.5,
Weight, kg, 13.0, no more,
Overall dimensions, mm, 384x301x169
MNIPI
Minsk
Produced in: Belarus, Minsk
Cable Searcher Athlete AG-318N
from
259 800 ₽
A trace searching kit for finding underground utilities (cable lines, metal pipelines, and other communications made of conductive materials).
The kit includes a receiver in the form of a monoblock with LED indication, as well as the most powerful multi-frequency generator in the TECHNO-AC line, with a range of up to 10 km.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
CS20-20 power supply
Operating Mode: Continuous
Output stabilized current, A: 0-20
Output voltage, V: 0-20
Power supply: Single-phase 220 V 50 Hz
Operating temperature range, °C: +10...+35
Storage temperature, °C: -20...+45
Relative humidity (without condensation), %: 90 Weight, kg: 3
Overall dimensions (W x H x D), mm: 205 x 200 x 80
INZHEKT
Saratov
Produced in: Saratov
Trace searcher with the function of saving GPS/GLONASS coordinates Success AG-309.20K
from
206 310 ₽
A trace searching kit for finding underground utilities (cable lines, metal pipelines, and other communications made of conductive materials).
As part of the kit, the receiver is in the form of a monoblock with a large LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line. Built-in GPS\GLONASS module for determining and recording the coordinates of the location of communication.
"Probe" mode for tracing NON-METALLIC communications using an in-line generator (optional).
Compact stand-alone generator with an output power of up to 20 watts and a range of up to 3 km. Connection to the desired route is possible both by contact and contactless method.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
High-frequency signal generator G4-233
NNPO im. M.V.Frunze
Nizhny Novgorod
Produced in: Nizhny Novgorod
Mobile laboratory for 0.4-10 kV cable lines (ETL-10)
Laboratory for 0.4-10 kV cable lines (ETL-10) consists of:
1. Test facility
• – Maximum rectified voltage up to 70 kV;
• – Maximum AC voltage of the industrial frequency of 50 Hz to 50 kV.
2. Burning facility
• – Maximum voltage up to 30 kV;
• – Maximum current up to 80 A;
• – Working hours are not limited;
• – Switching of stages is carried out without breaking the arc at the time of switching;
• – The ability to start working from any stage of burning (when working with low-voltage cables);
• – Built-in afterburning.
3. High voltage pulse generator
• – Output voltage 0...12 kV / 0...24 kV;
• – The pulse energy at each stage is 3000 J;
• – Built-in IDM for collaboration with the reflectometer.
4. Reflectometer
– Supports 3 methods of determining the location of damage:
• – By pulse reflectometry;
• – By the method of oscillatory discharge;
• – Pulse-arc method.
5. High-voltage cable defects detector
• – Determining the location and depth of the cable at a depth of up to 10 m;
• – Tracing at a distance of up to 10 km;
• – Search for live electrical cables;
• – Search for places where the pipeline and cable intersect;
• – Determining the places of damage to cable lines;
• – Site surveys before excavation;
• – Search for places of damage to the external insulation of the cable;
• – GPS\GLONASS coordinates recording and mapping of found communications;
• – Cable selection from the bundle;
• – Search for the place of damage by acoustic method.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region