Muffle furnace LF-7/11-V1

The LOIP LT-417b modification device consists of an immersion thermostat-circulator LOIP LT-400 and a working bath with a lean-to hinged lid. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +200 with tap water cooling °C Tvods+5 ...+200 Accuracy of temperature maintenance, °C ± 0.01 The error of setting the set temperature, not more than, ° C ± 0.02 Heater power, W 2200 Pump: max. flow rate, l/min 6...12 pressure, 0.4 bar Bath volume, l 17 The working fluid is water, silicone oil. Open part of the bath / depth, mm 360x296/150 Overall dimensions, mm 532x335x350 Weight, kg 14.4

The total volume of the chamber is 65 l Overall dimensions 480x620x1070 mm Weight 33 kg Power consumption 200 W

Purpose: obtaining distilled water of type 2 according to GOST R 58144-2018 "Distilled water", FS.2.2.0019.18 "Water for injection" Capacity: distillate: 5.0 (-10%) l/h, bidistillate: 4.3 (-10%) l/h. Heating elements: 1st stage of distillation: Heating element 3.5 kW 220V (stainless steel) – 1 pc., 2nd stage of distillation: Heating element 2.7 kW 220V (stainless steel) – 1 pc. The quality of the produced water: GOST R 58144-2018 "Distilled water", FS.2.2.0019.18 "Water for injection" Type of current, frequency, voltage: alternating single-phase, 50 Hz, 220 V Power consumption: in distillate production mode: 3.5 kW, in bidistillate production mode: 6.2 kW Overall dimensions (L×W×C), mm: 545×305×400 Weight: 16.5 kg Warranty period: 12 months from the date of sale Electrical conductivity of the produced water: bidistillate: 1.0-1.2 microns/cm, distillate: no more than 5.0 microns/cm The temperature of the produced water: distillate: from 70 to 85 ° C, bidistillate: no more than 40 ° C Source water consumption (at t of water 10 ° C) in the distillate production mode: 36 (±10%) l/h, in the bidistillate production mode: 88 (±10%) l/h Source water pressure: 0.1-0.4 MPa Version: Desktop with adjustable supports. Wall mounting is possible Coefficient of water purification from radionuclides: at least 4000 Service life: at least 8 years

Design features: Microprocessor-based PID controller; Multifunctional control knob; Efficient mixing system; Self-diagnosis system; Simple correction of internal temperature sensor readings; Two-point calibration; Built-in cooling coil; Technical specifications: Number of seats for viscometers 3 Temperature range - without external cooling, °C - with tap water cooling, °C - with cryostat cooling, °C (Current+10)...+150 (Tvods+5)...+150 0...+150 The error of setting the set temperature, ° C ± 0.02 Temperature maintenance error, ° C ± 0.01 Power consumption, W 1500 Overall dimensions, mm 380x235x560 Working depth, mm 300 Volume of working fluid, l 14 Weight of the device without liquid, kg 16

The vacuum condenser type trap with a capacity of 5 liters is designed to condense vapors of non-aggressive gases on the internal cooled surfaces of the trap, in order to prevent them from entering the pump.

The laboratory drying cabinet SNOL-F-25/350-I2 is designed for thermal testing, aging, as well as drying, tempering and other types of heat treatment of various materials in an air environment at temperatures up to 350 ° C with natural or forced air convection in stationary conditions.

Technical characteristics: NIP, G6100 Discreteness, g0,1 Self-calibration The size of the scale bowl / platform, mm175x145 The smallest weighing limit, g5,0 The price of the verification scale division, mg1000 Limits of permissible error during initial verification, mgot 5.0g to 5000g incl. ± 500; sv. 5000g to 6100g incl. ±1000 in accordance with GOST OIML R 76-1-2011 Accuracy class according to GOST OIML R 76-1-2011II is high Adjustment weight is built-in The setting time, s, no more than~2 7 years warranty

Vacuum resistance furnaces are necessary for heating products before pressure treatment, for sintering, degassing, quenching, annealing, soldering and chemical-technological processes. Such furnaces among all the variety of thermal equipment are considered the most environmentally friendly – heat treatment is carried out at t up to +2500 ° C in a purified vacuum. Under certain conditions, vacuum furnaces are used to work with neutral gases. The outer part of the furnace is made of stainless steel and is cooled by liquid. The inner part of the working chamber, where the heat treatment of materials is carried out, is made of an alloy of molybdenum and tungsten. The components are characterized by a low inertia force, reduced gas separation. The settings are available on the control panel, where the instruments, automatic and manual control switches are located. At every enterprise of the electronic industry, nuclear power, an explosion-proof vacuum resistance furnace is needed. The same applies to areas where various products undergo heat treatment at the stage of production and preparation for use.

Designation SSO-6.18/11 Power, kW 40 Diameter, mm 600 Height, mm 1800

Designation SNOL 8.25.3/2.5 P I2 Temperature, oS 250 Camera power, kW 12 Mandrel length 1500...2100 Opening the lid manually

Design features: Special system of air intake and exhaust of combustion products with adjustable thrust; Durable ceramic muffle; Semi-open heaters on four sides of the chamber; Microprocessor temperature controller; Conveniently located control panel and bright LED display; Ease of management and control; LED indicators of heater operation and protection operation; Automatic shutdown of heating when opening the door; The door opens up and faces the user with the cold side; Alarm when the current temperature exceeds the limits of the permissible range; Highly efficient thermal insulation of the housing; The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint. Technical specifications: Maximum heating temperature, °C +1300 Temperature stability in steady-state thermal mode, °C ± 10 Warm-up time to the maximum temperature, no more than 120 min Dimensions of the working chamber, WxHxD, not less than mm 215x190x330 Overall dimensions, WxHxD, not more than 525x1045x680 mm Rated supply voltage, 220 V Rated power, W 6100

The LOIP LT-212a modification device consists of an immersion thermostat-circulator LOIP LT-200 and a working bath with a flat removable lid. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +200 with tap water cooling °C Tvods+5 ...+200 Accuracy of temperature maintenance, °C ± 0.1 The error of setting the set temperature, no more than ° C ± 0.2 Heater power, W 2000 Pump: max. flow rate, l/min 10.5 pressure, 0.27 bar Bath volume, l 12 The working fluid is water, water-glycerin mixture, silicone oil. The open part of the bath / depth, mm 190x296/150 Overall dimensions, mm 355x335x370 Weight, kg 10.2

Characteristics The discreteness of setting the specified speed of rotation of the motor shaft is 10 rpm Resolution of displayed motor shaft rotation speed 10 rpm Resolution of displayed temperature (when using external temperature sensor PT1000) 0.1 °C Maximum armature length 80 mm Power consumption 20 W Connection – external temperature sensor PT1000 (sold separately) Dimensions, weight Overall dimensions, LxWxH 380x220x120 mm Weight 4.4 kg Contents of delivery 1) Primelab PL-R-basic mixer; 2) instruction manual combined with a passport; 3) anchor for the stirrer in a fluoroplastic shell 8*50 mm; 4) power cable with Euro plug. Notes The device controls the speed of rotation of the motor shaft, so the speed of rotation of the armature may differ from the speed of rotation of the motor shaft. The maximum rotation speed of the armature depends on the size of the mixing element, the volume and viscosity of the liquid, the shape of the vessel, etc.

Technical characteristics: NIP, G2100 Discreteness, g0,1 External calibration The size of the scale bowl / platform, mm175x145 The smallest weighing limit, g5 The limits of permissible error during primary verification, mgot 0.5g to 500 g incl. ±50; sv. 500g to 2000g incl. ±100; sv. 2000g to 2100g incl. ±150 in accordance with GOST OIML R 76-1-2011 Accuracy class according to GOST OIML R 76-1-2011II is high Weight adjustment 2KGF2* The time of setting the readings, s, no more than ~ 1 - 1.5 7 years warranty

Drying cabinet with manual vacuum adjustment SNVS-90/3.5 (or SNVS-4,3.4,3.4.9/3,5) It is intended for heat treatment of materials at temperatures up to 350 ° C with air access and in a vacuum controlled by manual valves. Thanks to modern temperature control, it demonstrates excellent performance of heat treatment modes. The measurement system complies with Russian standards and has certificates of entry into the SI State Register. Design for heat treatment in production and clean laboratories.

The tripod is made of aluminum, which allows them to be sterilized at any temperature; this material provides lightness and durability. It can be used in water baths. The tripod has an individual packaging. Designed for storing test tubes.

It provides clear visibility of the labels of viscometers located in the thermostat bath. This creates additional convenience and increases the accuracy of measurements. It is located behind the working bath of the thermostat.