Exhaust cabinet LAB-1600 ballscrews

NV-1200 SHV-M is the most low-budget exhaust cupboard of the NV line. It is single-frame, with a laminated countertop. It is intended mainly for analytical laboratories. External dimensions of the cabinet (W×D×H): 1100×700×1960 mm. Dimensions of the working area (W×D×H): 1068×540×750 mm. Table top: laminated chipboard. A minimalistic solution for your laboratory The NV-1200 SHV-M fume cupboard has a minimum of functions, which makes it the most inexpensive. The table top is made of laminated chipboard. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents. This countertop does not tolerate strong heating or prolonged exposure to solvents, concentrated acids and alkalis. The working area is closed by one lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1068×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, and at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, with the glass raised, the total height of the cabinet will be 2470 mm. The working area is illuminated by a fluorescent lamp (included in the package). The switch is located on the right side of the cabinet body. The base of the cabinet is made on an all-welded metal frame in powder coating. The side laminated panels (chipboard 16 mm thick) are edged on the facade with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a fairly uneven floor. And what are the other options? In the line of NV-1200 cabinets there is a cabinet with plumbing and a surface made of granite tiles, as well as cabinets without plumbing, and with a surface made of monolithic ceramics, stainless steel, chemically resistant plastic. They are exactly the same size as the NV-1200 SHV-M. If you need a minimalistic cabinet of large sizes, you could be interesteed in the NV-1500 SHV-M model.

The SHVM NVK 1200 MON is a metal fume cupboard for laboratory. The table top is made of monolithic ceramics, its width is 1200 mm. External dimensions of the cabinet (W×D×H): 1260×750×2250 mm. Internal dimensions of the camera (W×D×H): 1200×600×1168 mm. Table top material: monolithic ceramic. Reliable and durable construction The table top is made of a single ceramic plate with a width of 1200 mm. The seamless monolith of the countertop provides the highest reliability and durability. THe ceramics are great for all chemical laboratories, including those that work with substances at high temperatures. It perfectly tolerates heat, is moisture-resistant, resistant to acids and alkalis. High-temperature equipment (drying cabinets, muffle furnaces) can be placed on the table top. The cabinet has an all-welded metal frame covered with durable powder paint. All panels are made of polymer-coated metal. The front anti-spill side is made of polished stainless steel AISI-316. There are four exhaust zones in the working chamber: they are located in the hood of the exhaust box and just above the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. The hood area is also made of metal. The protective screen of the cabinet can be easily lifted with one hand. It folds up and when lifted does not increase the overall height of the cabinet. It is made of 4 mm tempered glass in an aluminum frame. The sockets and the switch of the LED lamp are located outside the working area, on the right-hand side of the front panel of the cabinet. The sockets are splash-proof and are designed for current up to 16 A and voltage up to 250 V. Next to the switch there is a toggle switch of the automatic emergency power off. The reagents needed for work can be placed in the lower cabinet also made of metal. The cabinet has three swing doors and one fixed shelf. It has its own hood (pipe diameter 100 mm), which can be connected to the general exhaust system of the cabinet using the nozzle included in the cabinet kit. The cabinet legs are adjustable in height, allowing you to place the cabinet even on a rather uneven floor. Advantages of the SHVM NVK 1200 MON cabinet A metal fume cupboard suitable for any laboratory; Durable, reliable and very convenient to use; The protective screen is made of tempered glass; A hood is built into the cabinet, reagents can be safely stored in it. Application of the SHVM NVK 1200 MON cabinet Exhaust laboratory cabinets are used when working with toxic and harmful volatile materials, with clean materials, with dissolution or decomposition under heat treatment, when conducting sample analysis. Fume cupboards of the NV-Comfort series are used in laboratories of the widest profile: at food and light industry enterprises, in higher educational and scientific institutions, in chemistry classrooms at school, in quality control centers, medical organizations.

The SHVM NVK 1500 MON+ is a large metal fume cupboard with plumbing fixtures for laboratory. The table top is made of monolithic ceramics, its width is 1200 mm. External dimensions of the cabinet (W×D×H): 1560×750×2250 mm. Internal dimensions of the camera (W×D×H): 1500×600×1168 mm. Table top material: monolithic ceramic. A reliable and durable fume cupboard for laboratory The table top is made of monolithic ceramics. It is perfect for all chemical laboratories, including those that work with substances at high temperatures. It perfectly tolerates heat, is moisture-resistant, resistant to acids and alkalis. High-temperature equipment (drying cabinets, muffle furnaces) can be placed on the countertop. The width of the ceramic plate is 1200 mm, that is, there will be one seam in the countertop. The cabinet is mounted on an all-welded metal frame covered with durable powder paint. All panels are made of polymer-coated metal. The front anti-spill side is made of polished stainless steel AISI-316. There are four exhaust zones in the working chamber: they are located in the hood of the exhaust box and just above the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. The hood area is also made of metal. The protective screen of the cabinet can be easily lifted with one hand. It folds up and when lifted does not increase the overall height of the cabinet. It is made of 4 mm tempered glass in an aluminum frame. The small sink-drain is made of polypropylene, it is resistant to aggressive chemicals. Its internal dimensions: 218×115×122 mm. The faucet is made of brass, covered with polypropylene. The sockets and the switch of the LED lamp are located outside the working area, on the right-hand side of the front panel of the cabinet. The sockets are splash-proof and are designed for current up to 16 A and voltage up to 250 V. Next to the switch there is a toggle switch of the automatic emergency power off. The reagents needed for work can be placed in the lower cabinet. The cabinet is also made of metal. It has three swing doors and one fixed shelf. It has its own hood (pipe diameter 100 mm), which can be connected to the general exhaust system of the cabinet using the nozzle included in the cabinet kit. The cabinet legs are adjustable in height, allowing you to place the cabinet even on a rather uneven floor. Advantages of the SHVM NVK 1500 MON+ cabinet A metal fume cupboard with plumbing, suitable for any laboratory; The wide table top allows you to organize the workplace as conveniently as possible; It is durable, reliable and very convenient to use; The protective screen is made of tempered glass; The hood is built into the cabinet, reagents can be safely stored in it. Application of the SHVM NVK 1500 MON+ cabinet Exhaust laboratory cabinets are used when working with toxic and harmful volatile materials, with clean materials, with dissolution or decomposition under heat treatment, when conducting sample analysis. Exhaust cabinets of the NV-Comfort series are used in laboratories of the widest profile: at food and light industry enterprises, in higher educational and scientific institutions, in chemistry classrooms at school, in quality control centers, medical organizations.

BASIC EQUIPMENT Working box front guide posts – aluminum profile painted with powder paint (RAL 7035/RAL 5023), in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) front anti–spill side - polypropylene working surface - polypropylene 15mm thick removable plate 600*600mm with a ceramic granite work surface for placement heating plates (2 pcs.) 2 dependent lifting screens filled with transparent PVC, 5mm thick in a polypropylene frame in the lower screen – sliding doors made of transparent PVC with a thickness of 5mm lifting 0-780mm, does not change the dimensions of the cabinet when lifting the counterweights are placed in the front pillars-pylons and are easily serviced upper fixed screen – polypropylene inner part the working box is a fully sealed polypropylene capsule with a back wall washing system, a drainage channel and a polypropylene pipe for cold water 3 levels of hoods easily removable polypropylene exhaust canopies polypropylene drain sink on the top panel are placed: LED dust- and moisture-proof lamp (2X22W IP65) separated from the workspace by transparent PVC switching box with automatic emergency power off 16A flange with damper plug for air inflow d=200mm flange with aspiration collector for air outflow d=250mm (distance from the rear panels up to the center of the flange – 155mm) cabinet ventilation system

The SHVM NVK 1500 MON is a metal fume cupboard for laboratory. The table top is made of monolithic piece of ceramics. External dimensions of the cabinet (W×D×H): 1560×750×2250 mm. Internal dimensions of the camera (W×D×H): 1500×600×1168 mm. Table top material: monolithic ceramic. A reliable and durable laboratory cabinet The table top is made of monolithic ceramics. It is perfect for all chemical laboratories, including those that work with substances at high temperatures. It perfectly tolerates heat, is moisture-resistant, resistant to acids and alkalis. High-temperature equipment (drying cabinets, muffle furnaces) can be placed on the countertop. The width of the ceramic plate is 1200 mm, that is, there will be one seam in the countertop. The cabinet is mounted on an all-welded metal frame covered with durable powder paint. All panels are made of polymer-coated metal. The front anti-spill side is made of the AISI-316 polished stainless steel. There are four exhaust zones in the working chamber: they are located in the hood of the exhaust box and above the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. The hood area is also made of metal. The protective screen of the cabinet can be easily lifted with one hand. It folds up and when lifted does not increase the overall height of the cabinet. It is made of 4-mm tempered glass in an aluminum frame. The sockets and the switch of the LED lamp are located outside the working area, on the right-hand side of the front panel of the cabinet. The sockets are splash-proof and are designed for current up to 16 A and voltage up to 250 V. Next to the switch there is a toggle switch of the automatic emergency power off. The reagents needed for work can be placed in the lower cabinet cabinet. The cabinet is also made of metal. The cabinet has swing doors and one non-removable shelf. It has its own hood (pipe diameter 100 mm), which can be connected to the general exhaust system of the cabinet using the nozzle included in the cabinet kit. The cabinet legs are adjustable in height, allowing you to place the cabinet even on a rather uneven floor. Advantages of the SHVM NVK 1500 MON cabinet A metal fume cupboard, perfect for any laboratory; The wide table top allows you to equip the workplace as conveniently as possible; It is durable, reliable and very convenient to use; The protective screen is made of tempered glass; The cupboard is built into the cabinet, reagents can be safely stored in it. Application of the SHVM NVK 1500 MON cabinet Exhaust laboratory cabinets are used when working with toxic and harmful volatile materials, with clean materials, with dissolution or decomposition under heat treatment, when conducting sample analysis. Fume cupboards of the NV-Comfort series are used in laboratories of the widest profile: at food and light industry enterprises, in higher educational and scientific institutions, in chemistry classrooms at school, in quality control centers, medical organizations.

The Korsa NV-1500 SHV-SPB Laboratory fume cupboard is a single—frame cabinet with a width of 1410 mm with a countertop made of chemical-resistant plastic. External dimensions of the cabinet (W×D×H): 1410×700×1960 mm. Dimensions of the working area (W×D×H): 1378×540×750 mm. Table top: chemically resistant plastic. A reliable fume cupboard for laboratories Working surface material: chemical resistant plastic. It is moisture-resistant, resistant to prolonged exposure to concentrated acids and alkalis. It has limited resistance to high temperature and to prolonged exposure to organic solvents. It is a popular choice for laboratories, suitable for training workshops, analytical and medical laboratories. Ovens or drying cabinets should not be placed on such a countertop. The working area is closed by one lifting frame with a counterweight. There are two exhaust zones in it: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1378×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, with the glass raised, the total height of the cabinet will be 2470 mm. The working area is illuminated by an LED lamp (included in the package). The switch is located on the right-hand side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets have the IP20 degree of protection, maximum load: 1.5 kW. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard 16 mm thick) are edged on the facade with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

The Kors NV-1500 SHVD-U laboratory fume cupboard is a two—frame cabinet with a granite countertop with a width of 1410 mm and a small built-in sink made of polypropylene. External dimensions of the cabinet (W×D×H): 1410×700×1960 mm. Dimensions of the working area (W×D×H): 1378×540×750 mm. Table top: granite tiles. Working surface material: porcelain tile. It is moisture-resistant and perfectly withstands high temperatures. It is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Limited resistance to hydrofluoric acid. This is one of the most popular types of countertops for laboratory furniture. The small sink-drain is made of polypropylene, resistant to aggressive chemicals. Its diameter is 135 mm and its depth is 110 mm. The working area is closed by two lifting frames with a counterweight. As standard, there are two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1378×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, when the glass is raised, the height of the cabinet will be 2470 mm. The NV-1500 SHVD-U fume cupboard is equipped with an LED lamp with a switch and two sockets, one of them with grounding. Sockets have the IP20 degree of protection, the maximum load on them: 1.5 kW. The working chamber is an all-welded metal frame in powder coating. Load-bearing laminated panels (chipboard with a thickness of 16 mm) are edged on the facade with a durable PVC edge with a thickness of 2 mm, which increases the impact resistance and mechanical strength of the products. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

Kors NV-1200 SHV-PB Laboratory fume cupboard is a single—frame cabinet with a width of 1100 mm with a table top made of polypropylene. External dimensions of the cabinet (W×D×H): 1100×700×1960 mm. Dimensions of the working area (W×D×H): 1068×540×750 mm. Table top: polypropylene. Convenient fume cupboards for comfortable work in the laboratory Working surface material: monolithic polypropylene. It is moisture-resistant, resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Poorly resistant to high temperatures. Polypropylene countertops are suitable for chemical laboratories that work a lot with concentrated inorganic acids and alkalis. The working area is closed by a single lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1068×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, when the glass is raised, the total height of the cabinet will be 2470 mm. The working area is illuminated by a fluorescent lamp (included in the package). The switch is located on the right side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets have the IP20 degree of protection, maximum load: 1.5 kW. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard with a thickness of 16 mm) are edged with a durable PVC edge with a thickness of 2 mm, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor. What are the other options? There are larger cabinets with polypropylene countertops: NV-1500 SHV-PB, NV-1500 SHVD-PB and NV-1800 SHVD-PB.

The Kors NV-1200 SHV-U laboratory fume hood is a single—frame cabinet with a ceramic granite countertop 1100 mm wide and a small built-in polypropylene sink. External dimensions of the cabinet (W×D×H): 1100×700×1960 mm. Dimensions of the working area (W×D×H): 1068×540×750 mm. Table top: granite tiles. Reliable fume cupboard for laboratories The cabinet is available in two versions: with a hood from the lower cabinet and without it. In a cabinet with a hood, various aggressive reagents can be stored, in a cabinet without a hood, it is better to store only laboratory glass or instruments. Working surface material: porcelain tile. It is moisture-resistant and perfectly withstands high temperatures. It is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Limited resistance to hydrofluoric acid. This is one of the most popular types of countertops for laboratory furniture. The small sink-drain is made of polypropylene, resistant to aggressive chemicals. Its diameter is 135 mm and its depth is 110 mm. The base of the cabinet is made on an all-welded metal frame in powder coating. The side laminated panels (chipboard 16 mm thick) are edged on the facade with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a fairly uneven floor. Working area of the fume cupboard The working area is closed by one lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1068×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it is small enough in length, otherwise you will not be able to close the cabinet. The working area is illuminated by a fluorescent lamp (included in the package). The switch is located on the right side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets have the IP20 degree of protection, maximum load: 1.5 kW. What are the other options? If you need to place large equipment, you may be interested in the cabinets for muffle furnaces. Also in the line there are large cabinets with plumbing fixtures: NV-1500 NV-U and two-frame NV-1500 SHV-U and NV-1800 SHV-U.

The Korsa NV-1500 SHV-NERZH Laboratory fume cupboards are single—frame cabinets with a width of 1410 mm with a stainless steel countertop. External dimensions of the cabinet (W×D×H): 1410×700×1960 mm. Dimensions of the working area (W×D×H): 1378×540×750 mm. Table top: stainless steel. Convenient fume cupboards for comfortable work in the laboratory Working surface material: stainless steel. It is well suited for biological or medical laboratories, but it is not recommended for use in chemical laboratories. It is resistant to prolonged exposure to temperature, organic solvents, and oils. It has limited resistance to short-term exposure to concentrated mineral acids and alkalis and is destroyed by prolonged exposure to concentrated acids. The working area is closed by a single lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1378×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, with the glass raised, the total height of the cabinet will be 2470 mm. The working area is illuminated by an LED lamp (included in the package). The switch is located on the right-hand side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets have the IP20 degree of protection, maximum load: 1.5 kW. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard with a thickness of 16 mm) are edged with a durable PVC edge with a thickness of 2 mm, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

Kors NV-1200 SHV-B laboratory fume hoods are single—frame cabinets with a width of 1100 mm with a countertop made of granite tiles. External dimensions of the cabinet (W×D×H): 1100×700×1960 mm. Dimensions of the working area (W×D×H): 1068×540×750 mm. Table top: granite tiles. Convenient fume cupboards for comfortable work in the laboratory The cabinet is available in two versions: with a hood from the lower cabinet and without it. In a cabinet with a hood, various aggressive reagents can be stored, in a cabinet without a hood, it is better to store only laboratory glass or instruments. Working surface material: porcelain tile. It is moisture-resistant, perfectly withstands high temperatures. It is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. It has limited resistance to hydrofluoric acid. This is one of the most popular choices for work surfaces, suitable for most laboratories. Drying cabinets or other highly heated appliances can be placed on such a countertop. The working area is closed by a single lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1068×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, with the glass raised, the total height of the cabinet will be 2470 mm. The working area is illuminated by a fluorescent lamp (included in the package). The switch is located on the right side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets with IP20 degree of protection, maximum load: 1.5 kW. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard with a thickness of 16 mm) are edged with a durable PVC edge with a thickness of 2 mm, which increases their impact resistance and mechanical strength. The legs of the cabinet are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

The Kors NV-1500 SHV-U laboratory fume cupboaed is a single—frame cabinet with a width of 1410 mm with a granite countertop and a small built-in sink made of polypropylene. External dimensions of the cabinet (W×D×H): 1410×700×1960 mm. Dimensions of the working area (W×D×H): 1378×540×750 mm. Table top: granite tiles. A practical cabinet for your laboratory The cupboard is available in two versions: with a hood from the lower cabinet and without it. In a cabinet with a hood, various aggressive reagents can be stored. In a cabinet without a hood, it is better to store only laboratory glass or instruments. Working surface material: porcelain tile. It is moisture-resistant and perfectly withstands high temperatures. It is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Limited resistance to hydrofluoric acid. This is one of the most popular types of countertops for laboratory furniture. The small sink-drain is made of polypropylene, resistant to aggressive chemicals. Its diameter is 135 mm and its depth is 110 mm. Working area size (W×D×H): 1378×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The working area is closed by a lifting frame with a counterweight. As standard, there are two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. A version with an additional hood from the lower cabinet is also available. The height of the raised glass above the cabinet: 510 mm, that is, when the glass is raised, the height of the cabinet will be 2470 mm. The NV-1500 SHV-U fume cupboard is equipped with a fluorescent lamp with a switch and two sockets, one of them with grounding. Sockets have the IP20 degree of protection, the maximum load on them: 1.5 kW. The working chamber is an all-welded metal frame in powder coating. Load-bearing laminated panels (chipboard with a thickness of 16 mm) are edged along the facade with a durable PVC edge with a thickness of 2 mm, which increases the impact resistance and mechanical strength of the products. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

The Korsa NV-1500 SHV-PB laboratory fume cupboard is a single—frame cabinet with a width of 1410 mm with a table top made of polypropylene. External dimensions of the cabinet (W×D×H): 1410×700×1960 mm. Dimensions of the working area (W×D×H): 1378×540×750 mm. Table top: polypropylene. A reliable fume cupboard for laboratories Working surface material: monolithic polypropylene. It is moisture-resistant, resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Poorly resistant to high temperatures. Polypropylene countertops are suitable for chemical laboratories that work a lot with concentrated inorganic acids and alkalis. The working area is closed by a single lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1378×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, with the glass raised, the total height of the cabinet will be 2470 mm. The working area is illuminated by an LED lamp (included in the package). The switch is located on the right-hand side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets have the IP20 degree of protection, maximum load: 1.5 kW. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard 16 mm thick) are edged on the facade with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

BASIC EQUIPMENT Working box front guide posts – aluminum profile painted with powder paint (RAL 7035/RAL 5023), in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) front anti–spill side - polypropylene working surface - polypropylene 15mm thick removable plate 600*600mm with a ceramic granite work surface for placement heating plates (2 pcs.) 2 dependent lifting screens filled with transparent PVC, 5mm thick in a polypropylene frame in the lower screen – sliding doors made of transparent PVC with a thickness of 5mm lifting 0-780mm, does not change the dimensions of the cabinet when lifting the counterweights are placed in the front pillars-pylons and are easily serviced upper fixed screen – polypropylene inner part the working box is a fully sealed polypropylene capsule with a back wall washing system, a drainage channel and a polypropylene pipe for cold water 3 levels of hoods easily removable polypropylene exhaust canopies polypropylene drain sink on the top panel are placed: LED dust- and moisture-proof lamp (2X22W IP65) separated from the workspace by transparent PVC switching box with automatic emergency power off 16A flange with damper plug for air inflow d=200mm flange with aspiration collector for air outflow d=250mm (distance from the rear panels up to the center of the flange – 155mm) cabinet ventilation system

Overall dimensions 1800x800x1905 mm Internal dimensions 1750x775x950 mm The diameter of the exhaust pipe is 200 mm Weight 165 kg

The Kors NV-1600 SHVp laboratory fume cupboard is a single—frame cabinet with a granite countertop with a width of 1544 mm and a porcelain apron. This is a specialized cabinet for placing heating devices: muffle furnaces, drying cabinets, laboratory stoves. External dimensions of the cabinet (W×D×H): 1600×888×1960 mm. Dimensions of the working area (W×D×H): 1544×660×1072 mm. Table top: granite tiles. Safe operation with laboratory furnaces The working surface and part of the working area are lined with granite tiles. The tile is moisture-resistant and perfectly withstands high temperatures. It is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Limited resistance to hydrofluoric acid. This is one of the most popular types of countertop materials for laboratory furniture. Height of the protective apron: 600 mm. Working area dimensions: 1544×660×1072 mm. Furnaces or cabinets up to 650 mm deep can be placed in the draft. The working area is closed by one lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. The fume cupboard is equipped with two sockets. Sockets have the IP20 degree of protection, maximum load: 4 kW. A reliable fume cupboard for heavy equipment placement The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard 16 mm thick) are edged on the facade with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

The Kors NV-1500 SHV-B laboratory fume cupboard is a single—frame cabinet with a width of 1410 mm with a countertop made of granite tiles. External dimensions of the cabinet (W×D×H): 1410×700×1960 mm. Dimensions of the working area (W×D×H): 1378×540×750 mm. Table top: granite tiles. A convenient fume cupboard for comfortable work in the laboratory The cupboard is available in two versions: with a hood from the lower cabinet and without such a hood. In a cabinet with a hood, various aggressive reagents can be stored, in a cabinet without a hood, it is better to store only laboratory glass or instruments. Working surface material: porcelain tile. It is moisture-resistant and perfectly withstands high temperatures. It is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Limited resistance to hydrofluoric acid. This is one of the most popular types of countertops for laboratory furniture. Working area dimensions (W×D×H): 1378×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, when the glass is raised, the height of the cabinet will be 2470 mm. The working area is closed by a lifting frame with a counterweight. As standard, there are two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. A version with an additional hood from the lower cabinet is also available (the flange diameter is also 150 mm). The NV-1500 SHV-B fume cupbpard is equipped with a fluorescent lamp with a switch and two sockets, one of them with grounding. Sockets have the IP20 degree of protection, the maximum load on them: 1.5 kW. The working chamber is an all-welded metal frame in powder coating. Load-bearing laminated panels (chipboard with a thickness of 16 mm) are edged along the facade with a durable PVC edge with a thickness of 2 mm, which increases the impact resistance and mechanical strength of the products. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.