Search

Designation SNO-34 Volume, l 34 Material of the working chamber ceramics Heating 4 sides Power consumption, W, max 10000 Minimum operating temperature, 0C 100

It is used to separate immiscible liquids in extraction procedures. Kinds:VD-1-1000 VD-1-125 VD-1-250 VD-1-500 VD-1-60

The hydrogen generator is equipped with its own microprocessor, with which you can control the operating modes of the device. It is microprocessor control that determines the autonomy of the device. Moreover, this allows you to control the basic and technical parameters of the device (pressure, flow rate, level of water poured into the tank, tightness of gas lines, electrolyzer current). For the manufacture of gas lines, exclusively inert materials are used. Technical specifications:

The device is equipped with a four-button keyboard, which is used to set parameters and control. The generator can operate in continuous mode for a long time. For refueling, especially pure or double-distilled water is used, and refueling can be done without turning off the device, on the go. Their advantage is that they significantly reduce, or even completely eliminate, the use of bottled gases to power chromatographs and gas analyzers. For nutrition, mainly double-distilled water is used, the quality of which must be no lower than grade B water according to OST 11.029.003–80, and the electrical resistivity must be no less than 1 Mohm x cm.

The devices operate from a single-phase AC electrical network with voltage from 187 to 242 W, frequency (50±1) Hz. Maximum safety of devices is achieved due to the absence of such a supply of substance in them, which could fill a chromatograph or laboratory in a short period of time. The performance of the device eliminates the occurrence of explosive situations, so the generator is considered safe to use.

WB series baths can be used for sample evaporation, incubation, defrosting, conduction of chemical reactions. Temperature setting range, oC +35…+95 Temperature error, oC ±1.0 is protected from excess temperature RAINBOW TSR-150S F-C Hydraulic thermostat Supply voltage, V 230+-10% Current consumption 6.5A Power consumption, 1500 W Overall dimensions L x W x H, mm 450 x 325 x 260 Overall dimensions of the bath L x W x H, mm 360 x 300 x 205 Total / engine capacity, 21.9/18.1 l

The NV-1000 MOP is a large table with a deep sink made of polypropylene and with a built—in dryer for 18 seats. It is designed for standing work: its height is 85 cm. Assembled dimensions (W×D×H): 1000×600×1650 mm. The table top is made of laminated chipboard. It has a built-in Stegler WJH0357F polypropylene sink, its internal dimensions (W×L×H): 490×390×290 mm. The polypropylene is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents and suits perfectly for washing laboratory dishes. The package includes a stainless steel mixer with flexible 300 mm tap connectors and a siphon. The upper part of the inclined shelves of the dryer, on which dishes are placed, is covered with a polypropylene insert to protect it against water and reagents. The 18 pins are also made of polypropylene. The side laminated panels of the table (chipboard 16 mm thick) are edged on the facade with a 2 mm PVC edge, which increases their impact resistance and mechanical strength. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor. Advantages of NV-1000 MOP tables A wide table with a polypropylene sink and dryer for 18 dishes. An inexpensive solution for laboratories that value the reliability and durability of furniture. The polypropylene is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Application of NV-1000 MOP tables Tables of the NV series are used in laboratories of the widest profile: at food and light industry enterprises, in scientific and educational workshops, in chemistry classrooms, quality control centers, medical organizations and many others.

A power supply for laser modules that differ in power and amperage. It is suitable for all green and IR laser modules.

Technical specifications Overall dimensions of the device (mm) 113*25*14 The service life of the built-in battery is at least 300 cycles within the warranty period of the device. The sensitivity anisotropy according to Cs137 (%) is not more than 30 The full charge time of the built-in battery from the USB port of the PC or charger is no more than 4 hours. Operating time Continuous operation from a fully charged built-in battery in conditions of natural radiation background: - without the use of sound/vibration alarm for at least 2 months; - without using wireless communication and sound/vibration alarm for at least 4 months. Maximum counting speed (imp/sec) 10000 The weight of the device (g) is not more than 50 Note The Atom Fast 8850 can use a cylindrical crystal with a diameter of 10 mm and a height of 40 mm without prior notice. The energy range of the recorded photon radiation (keV) is not less than 60 - 3000 keV Working size of the scintillation detector (mm) 8*8*50 The scope of delivery USB cable for charging the built-in lithium-ion battery 1 pc. Dosimeter set—top box Atom Fast - 1 pc. Packing box 1 pc. Carrying case — 1 pc.

The XRF analyzer BRA-135F is an energy dispersive spectrometer which can simultaneously determine the presence of up to twenty chemical elements - from 9F to 92U - in the analyzed sample. Samples can be in liquid, solid, powdered or deposited on a substrate. The analyzer captures concentrations from tenths of mg/kg. The model BRA-135F performs quantitative/semi-quantitative spectral analysis of steel and alloys. It also performs spectral analysis of oil, petroleum and other petroleum products, detecting in their composition even the smallest concentrations of impurities of various metals. The vacuum sample chamber and ultra-slim detector inlet provides a low detection limit in the range of light elements from 9F to 17Cl. The high-performance silicon drift detector (SDD) with an energy resolution of less than 135eV allows the separation of spectral lines of almost all elements, which makes the analysis of complex multicomponent substances (high-alloy steels, precision alloys, polymetallic ores, etc.) possible.

The devices are designed for: measurements and registration of the main indicators of the quality of electrical energy established by GOST 32144-2013 (GOST R 54149-2010) with registration of protocols according to GOST 33073-2014; measurements and registration of the main parameters of electrical energy in single-phase and three-phase electrical networks (including the effective values of voltages and currents with sinusoidal and distorted curves; active, reactive and full electrical power); measurements of parameters of secondary circuits (load capacity of measuring transformers and voltage drop) in electric energy metering systems and electric energy losses in power supply lines. functional test and verification of connection of meters of active and reactive power and energy, energy measuring converters of voltage, current at the places of their operation; functional test and verification of the connection of single-phase and three-phase electric energy meters without breaking current circuits to detect theft of electricity; measurements of electricity losses in the power supply line. The PKE-A energy tester provides registration with subsequent transfer to a personal computer (PC) of statistical data on the PKE: Values of the PCE according to GOST 30804.4.30 (GOST P 51317.4.30) and GOST 30804.4.7 (GOST P 51317.4.7) with a registration depth of 512 days; Values and durations of voltage dips and overvoltages; Values of the short-term dose of flicker; Parameters of the electrical network and vector diagrams with the depth of registration: - 24 hours for averaging time of 3 s, - 200 days for averaging time of 10 min. The program "Energy Monitoring ES" provides the formation of quality control protocols in the form of GOST 33073-2014.

The composition of the PM-3 verification module: Frequency comparator CHK7-1011; Universal frequency meter Ch3-86A; Universal voltmeter V7-79; Absorbed power wattmeter M3-108-2; High-frequency signal generator G4-229; High-frequency signal generator G4-230; Generator of test pulses G9-1A; Oscilloscope S1-177; DC power supply B5-79/1; Electronic switchboard of RF signals; AC power source B2-7 (2 pcs.); PC, printer; Basic load-bearing structures (BNC). Technical specifications Measurement ranges of time-frequency parameters of signals: Continuous oscillation frequency from 0.005 Hz to 17.85 GHz Pulse repetition rate from 0.01 Hz to 100 MHz The carrier frequency of the IM signal is from 100 MHz to 17.85 GHz Pulse duration from 10 ns to 1000 s Time interval from 0 to 1000 s Nominal values of the frequency of the studied signals are 2,048; 5,0; 10,0; 10,24 MHz Measurement errors of time-frequency parameters of signals: Frequency of continuous oscillations ± (2,4·10-10 - 4·10-3) Pulse repetition rate ± (2·10-7 - 2·10-3) The carrier frequency of the IM signal is ± 2·10-7 Pulse duration ± (1 - 200) ns Time interval ± (1 - 200) ns The relative deviation of the frequency of the studied signal from the reference frequency ± (5·10-13 - 2·10-12) Frequency of continuous oscillations ± (3·10-11 – 1,1·10-5) Pulse repetition rate ± (2·10-11 – 6·10-5) Carrier frequency of the IM signal ± (3·10-11 – 1,1·10-5) Pulse duration ± (1·10-8 – 7,2·10-4) Time interval ± (2·10-10 – 7,2·10-4) Nominal values of the reference signal frequency ± (2·10-11 – 2,4·10-10) General technical characteristics: The area occupied by the module is 8-12 m2 Weight, not more than 327 kg Power supply voltage from 198 to 242 V frequency (50 ± 0.5) Hz Power consumption, no more than 2400 VA

Purpose of the NEURONET TECHNOAS 4 Laboratory • – Universal educational complex of modern educational technologies; • – Mobile remote and educational office for the working coherence of the subjects of activity. The use of the NEURONET TECHNOAS 4 laboratory • – Hardware and software complex based on multifunctional neuro-modular systems of electroencephalographs-recorders "Encephalan-EEGR-19/26"; • – Improving the productivity and profitability of the work of teams with physio-psychological diagnostics and correction, with machine neuro-training on biofeedback; • – Biophysical individual adjustment of the central nervous system; • – Conscious development of new reflexive meaningful states, rapid assimilation of new knowledge, skills, skills and actions; • – Reduction of dangerous influences of the human factor in responsible professions (aviation and others); • – Improving the effectiveness of educational programs for special education, retraining and advanced training. NEURONET TECHNOAS 4 Laboratory Support System • – MKZ safety control module; • – Mass switches in all compartments; • – Smart Home system, continuous monitoring of all life support systems with video recording; • – Audible alarm; • – Light alarm; • – An autonomous power source from batteries with a 12/220 V voltage converter; • – 12 V - 220 V sockets; • – Hardware and software complex of neuro-modular systems of electroencephalographs-recorders "Encephalan-EEGR-19/26"; • – Hardware and software complexes of modern educational technologies integrated with the Central Control Unit (central control unit).

equipment side decorative panels – melamine 16mm thick all-welded frame made of rectangular metal profile painted with white powder paint adjustable supports