The holder with flat steel springs allows you to install and securely fix up to 6 verifiable thermometers with a diameter of the submerged part from 16 to 20 mm. It is designed for THERMOTEST 05 and THERMOTEST-05-1 thermostats.

Termeks

Tomsk

general laboratory

accessories

Tomsk

holder

Produced in: Tomsk

Set of devices for BNTI-05-04 State Standard 20287 method B

It is used in determining the pour point of petroleum products in accordance with the State Standard 20287 (method B).

Tomsk

Produced in: Tomsk

Set of devices State Standard 5066 method B

It is designed to be placed in a liquid thermostat CRYO T 05 01 and is used to determine the turbidity temperature and the beginning of crystallization of motor fuel in accordance with GOST 5066 (method B). For testing, an additional set of CRYO T 05 01 K devices is required.

Tomsk

Produced in: Tomsk

Spring THERMOTEST holder-DP1-3/9

Allows you to install and securely fix up to 6 verifiable thermometers with a diameter of the submerged part from 3 to 9 mm. The design of the holder eliminates damage to glass thermometers. It is designed for calibration thermostats THERMOTEST-100 and THERMOTEST-300.

Tomsk

Produced in: Tomsk

Set of devices EN 23015 (ASTM D97)

It is used for determining the turbidity or fluidity temperature of petroleum products in accordance with EN 23015 and ASTM D97. For testing, additional sets of devices BNTI 05 04 K and BNTI 05 04 3K are required.

Tomsk

Produced in: Tomsk

The spring holder for LT 300 or LT electronic thermometers allows you to simply and securely mount the temperature sensor on the walls of laboratory utensils so that it does not touch either its bottom or the wall. This allows temperature measurements to be carried out not only conveniently, but also correctly.

Tomsk

Produced in: Tomsk

Saint Petersburg

Produced in: Saint Petersburg

A set of VT-ro-2K devices

It is used in determining the density of petroleum products, resins, plasticizers and other chemical products by hydrometers in stainless steel cylinders with a height of 300 mm and internal diameters of 60.5 and 73 mm.

Tomsk

Produced in: Tomsk

A set of devices of the TMP-K

It is used to determine the corrosive effect of petroleum products on a copper plate in accordance with GOST ISO 2160, GOST 32329, GOST 6321 and GOST 2917.

Tomsk

Produced in: Tomsk

Set of devices CRYO-VIS-T-05-K

It is used in determining the low-temperature characteristics of petroleum products and organic chemical products in accordance with the State Standard 5066 (Method B) and GOST 18995.5.

Tomsk

Produced in: Tomsk

Set of devices GOST 11851 method A

It is intended for placement in the BF bath and is used in determining the mass fraction of paraffins in oil in accordance with the method A of the State Standard 11851.

Tomsk

Produced in: Tomsk

A set of BNTI devices-05-04- 4K

It is intended for placing vessels with samples in the working baths of the BNTI 05 04 bath when determining the low-temperature properties of petroleum products, if appropriate test vessels are available. Suitable for placing vessels with samples for the State Standard 20287 (Method A), EN 23015 or ASTM D97.

Tomsk

Produced in: Tomsk

Set of devices the State Standard 5960

It is used in determining the brittleness temperature of polyvinyl chloride plastic by express method in accordance with the State Standard 5960.

Tomsk

Produced in: Tomsk

Set of devices the State Standard 18995.5

It is used in determining the crystallization temperature in accordance with the State Standard 18995.5.

Tomsk

Produced in: Tomsk

Holder THERMOTEST-D1-3/9

The holder with flat steel springs allows you to install and securely fix up to 6 verifiable thermometers with a diameter of the submerged part from 3 to 9 mm. It is designed for calibration thermostats THERMOTEST-100 and THERMOTEST-300.

Tomsk

Produced in: Tomsk

Universal holder LA-122

Saint Petersburg

Produced in: Saint Petersburg

VIS-T-D2 Viscometer Holder

It is the holder with a screw clip for reference viscometers. It is designed for use in VIS T 06, VIS T 06 01 and VIS T 11 thermostats

Tomsk

Produced in: Tomsk

May be interested in

Transitional centering rings (aluminum / stainless steel) with O-ring of circular cross-section

The ISO-KF connection (DIN 28 403 and ISO 2861) allows quick installation and replacement of components in vacuum systems. The connection consists of two symmetrical ISO-KF flanges (1), a centering ring with an O-ring seal (2) and a quick-release clamp (3). High-vacuum ISO-KF connections can be mounted without using a tool by simply turning the nut of the quick-release clamp.

Kazan

Produced in: Kazan

It is used to connect TDS thermometers and MASTER thermostats equipped with an RS 485 interface to a personal computer via a USB interface. The use of this adapter does not require the installation of additional drivers because it uses the HID driver built into the operating system to exchange data.

Tomsk

Produced in: Tomsk

Tripod for test tubes LA-208

Number of sockets, pcs 15 Hole diameter, mm 22 Immersion depth, mm 200 Overall dimensions (WxDxH), mm 180x80x215

Saint Petersburg

Produced in: Saint Petersburg

CF plugs, non-rotating CF flanges

ConFlat (CF) standard connections are used to ensure the connection of components of vacuum systems operating in the field of high and ultra-high vacuum.

Kazan

Produced in: Kazan

Heating element for a 2.4 kW 220 V distiller

from 1 860 ₽

The tank for the 2.4 kW aquadistillator is made of stainless steel.

Belgorod

Produced in: Belgorod

Adapters for CF / ISO-KF SVB connections

ConFlat (CF) standard connections are used еo ensure the connection of components of vacuum systems operating in the field of high and ultra-high vacuum.

Kazan

Produced in: Kazan

Profile gasket without support ring

ConFlat (CF) standard connections are used to ensure the connection of components of vacuum systems operating in the field of high and ultra-high vacuum.

Kazan

Produced in: Kazan

Distilate cooler for the AE-25 distiller

from 8 550 ₽

The distillate cooler is installed directly on the body of the aquadistillator and provides cooling of the finished distillate from 80 ° C to 40 ° C.

Belgorod

Produced in: Belgorod

Holder THERMOTEST-D2-16/20

Tomsk

Produced in: Tomsk

Replacement O-rings for ISO-F flange connections

Kazan

Produced in: Kazan

Set of devices for BNTI-05-04 State Standard 20287 method B

It is used in determining the pour point of petroleum products in accordance with the State Standard 20287 (method B).

Tomsk

Produced in: Tomsk

Bolts and nuts for DIN flanges with a side

DIN EN 1092-1 fixed flange fittings.

Kazan

Produced in: Kazan

from 1 700 ₽

Designed for devices of the SF, Minigem, Specord series when operating in the spectral range from 260 to 2500 nm. Chemically resistant to acids (except hydrofluoric acid) and dilute alkalis.

Suponevo

Produced in: Bryansk region

Set of devices State Standard 5066 method B

Tomsk

Produced in: Tomsk

The basket with a lid is designed to accommodate unambiguous measures of electrical resistance in the MT-21 thermostat during their verification and calibration in accordance with GOST 8.237. Internal dimensions 103x170 mm Weight 0.3 kg

Tomsk

Produced in: Tomsk