Equipment

Purpose: obtaining distilled water of 3 types according to GOST R 58144-2018 "Distilled water", FS.2.2.0020.18 "Purified water" Capacity: 70.0 (-10%) l/h Heating elements: electrodes The quality of the produced water: GOST R 58144-2018 "Distilled water", FS.2.2.0020.18 "Purified water" Type of current, frequency, voltage: alternating three-phase, 50 Hz, 380 V Power consumption: 42.0 kW Overall dimensions (L×W×C), mm: 740×550×1010 Weight: 64 kg Warranty period: 14 months from the date of sale Registration certificate for a medical device No. FSR 2008/03707 dated December 05 , 2008 Electrical conductivity of the produced water: 3-4.5 microns/cm The temperature of the produced water: 50 °C Source water flow rate (at 10 °C water temperature): 500 (+-10%) l/h Source water pressure: 0.1-0.4 MPa Overall dimensions of the control unit (L×W×C), mm: 400×220×500 Execution: outdoor Coefficient of water purification from radionuclides: at least 4000 Service life: at least 8 years

Technical specifications: Performance 4l/h Storage tank capacity 8 l Water consumption 54 l/h Electrical conductivity of the distillate, no more 2.5 mcm/cm Food 220 V / 50 Hz Power consumption 3 kW Overall dimensions 620x320x493 Weight 21.5kg

The measurement range of arsenic in waters, soil, and food products allows the determination of arsenic at concentrations well below the permissible level (maximum permissible concentration).

The GVCH-6 hydrogen generators are designed to power flame ionization detectors. They are equipped with a four-stage gas purification system. The hydrogen capacity is 6 liters/hour (100 ml/min). They have smooth adjustment and digital indication of the output pressure. Technical specifications The brand of produced hydrogen "A" according to GOST 3022-80 Purity of hydrogen in terms of dry gas is about 99.995% The concentration of water vapor at 20 ° C and 1.0 ati is not more than 20 ppm Total hydrogen capacity reduced to normal conditions is 6 l/h The range of the specified output pressure of hydrogen is from 1.5 to 6.0 ati Stability of the output pressure of hydrogen is not worse than ± 0.02 ati The time of setting the operating mode is no more than 30 min Volume of bidistilled water to be filled is 1 l Consumption of bidistilled water is no more thann 0.01 l/hour Consumption of bidistilled water is 1.6 g/l of hydrogen Average power consumption in stationary mode is no more than 100 VA Maximum power consumption (at startup) is no more than 150 VA Overall dimensions of the generator, (width x depth x height) are not more than 180x450x435 mm The mass of the generator is not more than 11 kg Working conditions: ambient temperature, °C from +10 to +35 Power supply from single-phase mains: AC voltage, 220±10% and frequency, Hz 50 ± 1

a massive copper mold was used in the furnace, as well as a printed crucible made of stabilized (calcium oxide) zirconium dioxide. The furnace has been working for several years at one of the non-ferrous metallurgy enterprises in the production of platinum ingots according to GOST

The working condition of the ND-400(R) diffusion pump depends on the temperature of the working fluid in the pump boiler. During the initial filling, it is recommended to fill the maximum volume of the working fluid. Working fluid is "VACMA OIL 500" vacuum oil (under technical specifications TU 19.20.29-061-00218526-2019). The total amount of working fluid in the ND-400(R) diffusion pump is a maximum of 5 liters, a minimum of 3.3 liters. The viewing window for visual inspection of the working fluid has marks of its maximum and minimum amounts. During normal operation of the pump, the level of the working fluid practically does not change. The temperature of the working fluid when the pump is operating at the maximum residual pressure is about 240°C to 255°C. It is recommended to monitor the operation of heaters in the ND-400(R) diffusion pump using one temperature sensor. The temperature sensor must be installed in a special radiator socket above the heater. If there is a loss of working fluid and an increase in the temperature of the radiators of the ND-400(P) diffusion pump to 320°C, the temperature sensor must give the command to automatically turn off the heaters. The subsequent activation of the pump heaters should not be automatic and should be performed only after cooling the system. Water at the inlet to the cooling systems of the housing and the oil reflector must be supplied with a pressure of 0.3 MPa (3 kgf/cm2) to 0.5 MPa (5 kgf/cm2) and a temperature of plus 4°C to plus 25°C. The recommended cooling water consumption for the housing is 250 l/h, for the oil reflector it is 40 l / h. It is regulated by the outlet water temperature, which should not exceed plus 40°C. The water drain should be free (with a jet break).

Capacity: 25.0 (- 10%) l/h Heating elements: Heating ELEMENT 2.6 kW 220V (stainless steel) – 6 pcs. The quality of the produced water: FS.2.2.0019.18 "Water for injection", GOST R 58144- 2018 "Distilled water" Type of current, frequency, voltage: three-phase alternating, 50 Hz, 380 V Power consumption: 15.0 kW Overall dimensions (L×W×C), mm: 355×310×580 Weight: 15.6 kg Warranty period: 24 months from the date of sale Registration certificate for a medical device No. FSR 2010/07649 of November 01 , 2016 Electrical conductivity of the produced water: 2-2.5 microns/cm The temperature of the produced water: from 70 to 85 ° C Source water flow rate (at 10 °C water temperature): 180 (±10%) l/h Source water pressure: 0.1-0.4 MPa Overall dimensions of the control unit (L×W×C), mm: 255×95×200 Version: Desktop with adjustable supports, Wall mounted (bracket is purchased separately) Coefficient of water purification from radionuclides: at least 4000 Service life: at least 10 years

It is designed to maintain a set temperature of a liquid coolant circulating both in an internal bath and in external consumers of a closed or open type. Pump for closed or open type thermostating systems. With a set of devices VT20-4K can be used for testing samples of asphalt concrete and oil bitumen. The operating temperature range is +20...+200 °C. Bath volume 20 l Overall dimensions 490x330x450 mm The open part of the bath is 240x200 mm Bath depth 210 mm Weight 16 kg Power consumption 2.2 kW.

It is designed to maintain the set temperature of the coolant circulating in the internal bath of the thermostat and in the connected external consumers. Feed pump for external closed-type thermostating systems. Cooling capacity 250 W at +20 °C. An internal bath with a volume of 6 liters and a depth of 140 mm. The operating temperature range is -20...+200 °C. Overall dimensions 280x460x620 mm The open part of the bath is 110x80 mm Bath depth 140 mm Weight 34 kg The power consumption is 2.5 kW.

The electric drying cabinet SHS-14/2.5-C is designed for drying, heating various materials in an air environment at a maximum temperature of 250 ° C. Technical specifications The electric cabinet operates at ambient temperature from 10 to 35 ° C and relative humidity up to 80% at 25 ° C. Operating temperature- 250 ⁰C Power consumption - 1000 watts Dimensions of the working chamber WxDxH- 195x340x195 mm Dimensions WxDxH- 325x600x345 mm Weight - 16 kg

Technical specifications: Melt flow rate for 10 min, g 0,1 - 99,9 The dimensions of the capillary opening, mm dia. 2,095 diam. 1,048 (optional) diam. 1,180 (optional) Set of loads, kg 0,325-5 10-21,6(optional) Temperature range in the working chamber, °C +50...+450 Accuracy of temperature maintenance, °C: - in the range of 50...300 °C: ± 0.1 - in the range of 300...350 ° C: ± 0.2 - in the range of 350...450°C: ±0.3 The discreteness of setting the temperature of the chamber, ° C 1 Time to enter the operating mode, no more, min 40 Power supply, V/kW 220/0.8 Installation dimensions, WxDxH mm 513x445x590 (920 – Maximum height with a fully loaded polymer chamber and a full stack of loads with a handle for their installation) Installation weight, not more than 70 kg