Catalog
Back to search results
Electronic explosion-proof thermometer ExT-01/2-6
Back to search results
Electronic explosion-proof thermometer ExT-01/2-6
The thermometer sensor ExT-01/2-6 is made in the form of a fully submersible probe with a cable length of 6 meters.
The thermometer has an explosion protection marking 0Ex ia IIB T4 Ga X and can be used in explosive zones 0, 1 and 2 of any classes of premises and outdoor installations in which the formation of explosive mixtures of categories IIA, IIB is possible.
• Measurement range -50...+130 °C
Minimum sensor immersion depth full immersion
Overall dimensions of the electronic unit 135x65x40 mm
Electronic unit weight 0.3 kg
The thermometer has an explosion protection marking 0Ex ia IIB T4 Ga X and can be used in explosive zones 0, 1 and 2 of any classes of premises and outdoor installations in which the formation of explosive mixtures of categories IIA, IIB is possible.
• Measurement range -50...+130 °C
Minimum sensor immersion depth full immersion
Overall dimensions of the electronic unit 135x65x40 mm
Electronic unit weight 0.3 kg
Continuous measurement of temperature in the industrial area
Appointment: the continuous measurement system allows for continuous measurement of the heating temperature of the industrial bucket, to improve the stability and reliability of measuring the temperature of liquid metal. Due to the fixed measurement position, the system eliminates errors due to the human factor. This method of measuring temperature was researched and invented on the theory of an absolutely black body. The principle of the temperature measurement system is the immersion of a temperature probe into molten steel to determine the temperature. The temperature probe made of an absolutely black body is designed in a special way to receive an infrared radiation signal corresponding to the temperature of molten steel.
Scope of application: Intermediate bucket
Measuring range:
Warming up the promkovsh: from 800°C to 1400°C; Molten steel: from 1400°C to 1600°C
Accuracy: Preheating of the promkovsh 7 ° C; Molten steel: 3 ° C
Response time: Hot response time 75 sec;
Cold response time 4 min
Measuring probe length: 964mm, 1100mm
Durability of measuring probes: 12 hours, 24 hours, 48 hours
Number of thermal shocks: up to 5 times
EVRAZPRIBOR
Lipetsk
Produced in: Lipetsk
Smart probe of relative humidity and temperature L=500 mm SSVL.500P with built-in flash memory
from
14 400 ₽
The smart probe of relative humidity and temperature L=500 mm with a built-in flash memory is designed to measure the temperature of gaseous materials without mechanical impurities and aggressive vapors, relative humidity by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitor based on the Android program.
Operating conditions of the SZVL.500P smart probe
Ambient temperature, °C: -20...+55.
Relative humidity, %: not more than 80 at T=35 °C.
Atmospheric pressure, kPa: 86...106.
Functionality of the smart probe SSVL.500P
Measurement of physical quantities with a resolution of 0.01.
Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory).
Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitorbased on the Android program.
Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor based on the Android program.
Automatic transition to sleep mode after 50 seconds.
The ability to connect an external power supply.
Possibility of calibration.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Thermoanemometer-hygrometer-barometer EcoTerma Maxima 01
from
52 900 ₽
Eco-E
Москва
Produced in: Moscow
Surface smart probe L=150 mm SZPV.150
from
10 920 ₽
The surfaCE SMART probe L=150 mm SZPV.150 is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor based on the Android program.
Operating conditions of the SZPV.150 smart probe
Ambient temperature, °C: -20...+55.
Relative humidity, %: not more than 80 at T=35 °C.
Atmospheric pressure, kPa: 86...106.
Functionality of the SZPV.150 smart probe
Measurement of physical quantities with a resolution of 0.01.
Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory).
Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor based on the Android program.
Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor based on the Android program.
Automatic transition to sleep mode after 50 seconds.
The ability to connect an external power supply.
Possibility of calibration.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Smart air probe L=1000 mm SSV.1000P with built-in flash memory
from
14 214 ₽
Designed to measure the temperature of various materials by direct contact of the probe with the measuring object
The smart air probe L=1000 mm SSV.1000P with built-in flash memory is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor. Android program is installed.
Operating conditions of the SZV.1000P smart probe
Ambient temperature, °C: -20...+55.
Relative humidity, %: not more than 80 at T=35 °C.
Atmospheric pressure, kPa: 86...106.
Functionality of the smart probe SSV.1000P
Measurement of physical quantities with a resolution of 0.01.
Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory).
Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor. Android program is installed.
Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed.
Automatic transition to sleep mode after 50 seconds.
The ability to connect an external power supply.
Possibility of calibration.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Smart probe of relative humidity and temperature L=500 mm SSVL.500
from
15 801 ₽
The smart probe of relative humidity and temperature L=500 mm SSVL.500 is designed to measure the temperature of gaseous materials without mechanical impurities and aggressive vapors, relative humidity by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitor based on the Android program.
Operating conditions of the SZVL.500 smart probe
Ambient temperature, °C: -20...+55.
Relative humidity, %: not more than 80 at T=35 °C.
Atmospheric pressure, kPa: 86...106.
Functionality of the smart probe SSVL.500
Measurement of physical quantities with a resolution of 0.01.
Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory).
Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor based on the Android program
Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor based on the Android program.
Automatic transition to sleep mode after 50 seconds.
The ability to connect an external power supply.
Possibility of calibration.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Smart probe for connecting an external thermoelectric converter of the CVT
from
10 626 ₽
Designed to measure the temperature of various materials by direct contact of the probe with the measuring object.
The smart probe for connecting an external thermoelectric converter is designed to measure the temperature of various materials by directly contacting the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitor based on the Android program.
Operating conditions of the smart probe of the SSVT
Ambient temperature, °C: -20...+55.
Relative humidity, %: not more than 80 at T=35 °C.
Atmospheric pressure, kPa: 86...106.
Functionality of the smart probe of the SSVT
Measurement of physical quantities with a resolution of 0.01.
Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory).
Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor. The Android program is installed.
Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor.The Android program is installed.
Automatic transition to sleep mode after 50 seconds.
The ability to connect an external power supply.
Possibility of calibration.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Meter recorder IS-203.3
from
34 431 ₽
The IS-203.3 meter-recorder is designed to measure and convert analog signals from primary converters (temperature, pressure, humidity, etc.) into the value of the measured physical quantity, as well as to register measuring information in the device's memory and then transfer it to a computer (RS 485 or USB) for visualization in the form of tables and graphs.
The meter recorder is a microprocessor-based meter equipped with a non-volatile storage device and a real-time clock. The device has the ability to work as a network device (up to 20 network devices at the same time) or stand-alone with subsequent connection to computers (laptop) for reading data.
The operating conditions of the meter IS-203.3
Ambient temperature, °C: -30...+50.
Relative humidity, %: up to 90.
Atmospheric pressure, kPa: 70...106.7.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Smart probe of relative humidity and temperature L=1000 mm SSVL.1000
from
16 560 ₽
The smart probe of relative humidity and temperature L=1000 mm SSVL.1000 is designed to measure the temperature of gaseous materials without mechanical impurities and aggressive vapors, relative humidity by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitor based on the Android program.
Operating conditions of the SZVL.1000 smart probe
Ambient temperature, °C: -20...+55.
Relative humidity, %: not more than 80 at T=35 °C.
Atmospheric pressure, kPa: 86...106.
Functionality of the smart probe SSVL.1000
Measurement of physical quantities with a resolution of 0.01.
Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory).
Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor based on the Android program.
Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor based on the Android program.
Automatic transition to sleep mode after 50 seconds.
The ability to connect external power.
Possibility of calibration.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
The self-recording meter IS-203.1.1
from
9 798 ₽
The measuring recorder IS-203.1.1 is designed to measure and register temperature with a specified time interval between measurements by direct contact of the device with the measuring object.
The features of the meter IS-203.1.1
Ease of operation.
Reliability.
The operating conditions of the meter IS-203.1.1
Ambient temperature, ° C: -30...+85.
Relative humidity, %: no more than 80% at T = 35 ° C.
Atmospheric pressure, kPa: 86...106.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Laboratory electronic thermometer LTA-E
It can be used as an accurate universal thermometer for contact temperature measurement of non-aggressive liquid, bulk and gaseous media.
It can be connected to a computer for calibration and transmission of measurement results.
• Range of temperature measurements -50...+200 °C
The minimum immersion depth of the sensor is 75 mm
Overall dimensions of the electronic unit 80x75x100 mm
Weight 0.25 kg
Termeks
Tomsk
Produced in: Tomsk
Oilman's Kit-1
from
67 254 ₽
It is designed to measure the temperature during the transportation of petroleum products, namely, to make a temperature correction for the volumetric expansion of petroleum products. The density of petroleum products decreases significantly with increasing temperatures, and the volume of the product increases, the kit "Oilman-1" allows temperature measurements for the subsequent calculation of the volumetric expansion of petroleum products.
•
TEKHNO-AS
Kolomna
Produced in: Moscow
Smart Atmospheric Pressure Probe with built-in flash memory
from
10 074 ₽
Designed to measure the temperature of gaseous materials without mechanical impurities and aggressive vapors, atmospheric pressure.
The smart atmospheric pressure probe with built-in flash memory is designed to measure the temperature of gaseous materials without mechanical impurities and aggressive vapors, atmospheric pressure by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitor based on the Android program.
Operating conditions of the SZDAP smart probe
Ambient temperature, °C: -20...+55.
Relative humidity, %: not more than 80 at T=35 °C.
Atmospheric pressure, kPa: 86...106.
Functionality of the smart probe SZDAP
Measurement of physical quantities with a resolution of 0.01.
Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory).
Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor. The Android program is installed.
Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor. The Android program isinstalled.
Automatic transition to sleep mode after 50 seconds.
The ability to connect an external power supply.
Possibility of calibration.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Laboratory electronic thermometer LT-300-F
The measurement range is -50...+200 °C.
Resolution 0.01 °C, error ±0.05 °C (Class C according to ASTM E2877).
The minimum immersion depth of the sensor is 75 mm
Overall dimensions of the electronic unit 75x80x35 mm
Weight 0.2 kg
Termeks
Tomsk
Produced in: Tomsk
Oilman's Kit
from
58 491 ₽
It measures temperature when checking the quality of fuel in samplers.
•
TEKHNO-AS
Kolomna
Produced in: Moscow
High-precision smart surface probe L=150 mm SZPWT.150
from
14 490 ₽
The high-precision smart surface probe L=150 mm SZPVT.150 is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitor, Android program.
Operating conditions of the SZPVT.150 smart probe
Ambient temperature, °C: -20...+55.
Relative humidity, %: not more than 80 at T=35 °C.
Atmospheric pressure, kPa: 86...106.
Functionality of the smart probe SZPVT.150
Measurement of physical quantities with a resolution of 0.01.
Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory).
Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed.
Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed.
Automatic transition to sleep mode after 50 seconds.
The ability to connect an external power supply.
Possibility of calibration.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Wall-mounted Smart Relative Humidity and Temperature Probe
from
13 920 ₽
The smart relative humidity and temperature probe wall-mounted SZVLN is designed to measure the temperature of gaseous materials without mechanical impurities and aggressive vapors, relative humidity by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitorbased on the Android program.
Operating conditions of the SZVLN smart probe
Ambient temperature, °C: -20...+55.
Relative humidity, %: not more than 80 at T=35 °C.
Atmospheric pressure, kPa: 86...106.
Functionality of the smart probe SZVLN
Measurement of physical quantities with a resolution of 0.01.
Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory).
Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor. The Android program is installed.
Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor. The Android program is installed.
Automatic transition to sleep mode after 50 seconds.
The ability to connect external power.
Possibility of calibration.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Pressure gauge MTIf-160
Pressure gauge with a range of measured pressure 0...160 kPa.
Accuracy class 0.4
Connection size M20x1.5 mm
Overall dimensions 160 mm
Weight 1.5 kg
Termeks
Tomsk
Produced in: Tomsk
Liquid low-temperature thermostat CRYO-VIS-T-07
Operating temperature range +10...+60 °C
Five places for glass viscometers.
The stability and uniformity of the temperature in the working bath is not worse than ± 0.01 ° C.
Bath volume 20 l
Overall dimensions 620x400x970 mm
The open part of the bath is 240x170 mm
Bath depth 300 mm
The size of the viewing window is 205x260 mm
Weight 60 kg
Power consumption 3.5 kW
Termeks
Tomsk
Produced in: Tomsk
Laboratory electronic thermometer LTA-E
It can be used as an accurate universal thermometer for contact temperature measurement of non-aggressive liquid, bulk and gaseous media.
It can be connected to a computer for calibration and transmission of measurement results.
• Range of temperature measurements -50...+200 °C
The minimum immersion depth of the sensor is 75 mm
Overall dimensions of the electronic unit 80x75x100 mm
Weight 0.25 kg
Termeks
Tomsk
Produced in: Tomsk
Laboratory electronic thermometer LT-300-F
The measurement range is -50...+200 °C.
Resolution 0.01 °C, error ±0.05 °C (Class C according to ASTM E2877).
The minimum immersion depth of the sensor is 75 mm
Overall dimensions of the electronic unit 75x80x35 mm
Weight 0.2 kg
Termeks
Tomsk
Produced in: Tomsk
Electronic explosion-proof thermometer ExT-01/1
The thermometer sensor ExT-01/1 is made in the form of a thin detachable probe without an extension cable.
The thermometer has an explosion protection marking 0Ex ia IIB T4 Ga X and can be used in explosive zones 0, 1 and 2 of any classes of premises and outdoor installations in which the formation of explosive mixtures of categories IIA, IIB is possible.
• Measurement range -50...+130 °C
The minimum immersion depth of the sensor is 75 mm
Overall dimensions of the electronic unit 135x65x40 mm
Electronic unit weight 0.3 kg
Termeks
Tomsk
Produced in: Belgorod, Tomsk
Laboratory electronic thermometer LT-300-N-TS
The measurement range is -50...+300 °C.
Up to +200 °C resolution 0.01 °C, error ±0.05 ° C.
Termeks
Tomsk
Produced in: Tomsk
Laboratory electronic thermometer LTA-NF
LTA-NF provides an error of ±0.05 °C in the range of measured temperatures from -50 to +200 ° C
The minimum immersion depth of the sensor is 75 mm
Overall dimensions of the electronic unit 80x75x100 mm
Weight 0.25 kg
Termeks
Tomsk
Produced in: Tomsk
Electronic explosion-proof thermometer ExT-01/2-15
The thermometer sensor ExT-01/2-15 is made in the form of a fully submersible probe with a cable length of 15 meters.
The thermometer has an explosion protection marking 0Ex ia IIB T4 Ga X and can be used in explosive zones 0, 1 and 2 of any classes of premises and outdoor installations in which the formation of explosive mixtures of categories IIA, IIB is possible.
• Measurement range -50...+130 °C
Minimum sensor immersion depth full immersion
Overall dimensions of the electronic unit 135x65x40 mm
Electronic unit weight 0.3 kg
Termeks
Tomsk
Produced in: Tomsk
EPR spectrometer CMS8400 NEO
The CMS8400 NEO is a compact electron paramagnetic resonance spectrometer designed for routine research in physics, chemistry, biology and related scientific fields for direct detection of free radicals and paramagnetic materials. The CMS8400 NEO can be used in both laboratory and industrial settings in the mode of on-line measurements, embedded in technological processes, thus providing control of parameters and reactions in the production process.
Additional accessories and adapted software can make the spectrometer an analytical tool and allow to implement new complex applications in medicine, petrochemistry, brewing, sanitary and hygienic control, as well as in other industries.
ADVIN Smart Faktory
Minsk
Produced in: Belarus
Laboratory electronic thermometer LT-300-T
The measurement range is -50...+300 °C.
Up to +200 °C resolution 0.01 °C, error ±0.05 °C (Class C according to ASTM E2877).
The minimum immersion depth of the sensor is 75 mm
Overall dimensions of the electronic unit 75x80x35 mm
Weight 0.2 kg
Termeks
Tomsk
Produced in: Tomsk
Laboratory electronic thermometer LTA-K
A compact temperature sensor on an elastic cable allows you to get to the most inaccessible places of the certified equipment.
LTA-K can be used as an accurate universal thermometer for contact temperature measurement of non-aggressive liquid, bulk and gaseous media.
The error is ± 0.05 °C in the range of -50...+200 °C.
Minimum sensor immersion depth full immersion
Overall dimensions of the electronic unit 80x75x100 mm
Weight 0.25 kg
Termeks
Tomsk
Produced in: Tomsk
Measuring air-thermal installation ASESH-8-1
1 supp.
A thermogravimetric (air-thermal) method for determining the mass fraction of moisture is implemented, based on measuring the mass of the sample of the analyzed substance before and after drying, followed by calculating the values of the mass fraction of moisture.
Air-thermal measuring installations ASESH-8 are registered in the State Register of Measuring Instruments under No.58526-14, have a certificate of approval of the type of measuring instruments RU.C.31.005 And No. 56847. The installations undergo initial verification and have the appropriate certificate.
GENERAL CHARACTERISTICS
1. Convenient access to the cells of the drying chamber
On the front side of the cabinet there are four doors for access to the cells.
2. The possibility of simultaneous determination of the humidity of 8 samples
The drying chamber of the air-heat installation consists of 8 independent cells with a total capacity of 16 bucs.
3. Built-in timer
The ASESH-8-1 installation has 4 timers, by means of which the end of the drying process is monitored in each section with the output of an audible signal and a light indication.
4. Natural ventilation
The absence of rotating elements ensures absolute noiselessness of operation and a long service life.
SCOPE OF APPLICATION:
1. Crop production, agriculture and forestry.
2. Products of meat, dairy, fish, flour-milling, feed and microbiological industries.
3. Food industry products.
4. Cellulose, paper, cardboard and products made from them.
5. Medicines, chemical and pharmaceutical products and medical products.
6. Building materials.
7. Products of the logging and sawmilling and woodworking industry.
8. Soils, пground, mineral fertilizers.
GK EKAN
Saint Petersburg
Produced in: Saint Petersburg
Laboratory electronic thermometer LT-300-N
The measurement range is -50...+300 °C.
Up to +200 °C resolution 0.01 °C, error ±0.05 °C (Class C according to ASTM E2877).
The minimum immersion depth of the sensor is 75 mm
Overall dimensions of the electronic unit 75x80x35 mm
Weight 0.2 kg
Termeks
Tomsk
Produced in: Tomsk
DIGITAL VACUUM METERS
A digital vacuum gauge is a device for measuring pressure in rarefied gases. The device is used for the study of chemical and physical processes in the steel, chemical industry, for setting up machine units. It is used to evaluate the performance of electronic lamps, when filtering various media. In this article we will consider the principle and features of the device, its purpose and the specifics of the choice.
Technical specifications:
To measure vacuum in medium and highly discharged environments, it is necessary to select sensitive equipment. The device must have the following characteristics:
Wide range of measured pressure (from 10-3 torr);
High sensitivity: up to 1 atm;
Absence of rubbing mechanical parts;
Support for different display units: torrs, pascals, mmHg
Support for different display units: torrs, pascals, mmHg;
Visual electronic display;
Insignificant power consumption.
NPF "META-KHROM"
Yoshkar-Ola
Produced in: Yoshkar-Ola, Mari El
Laboratory electronic thermometer LTA-MT
LTA-MT provides an error of ±0.2 °C in the measured temperature range from -196 to +300 °C
The minimum immersion depth of the sensor is 75 mm
Overall dimensions of the electronic unit 80x75x100 mm
Weight 0.25 kg
Termeks
Tomsk
Produced in: Tomsk