Search

Stem cell factor is a growth factor produced mainly by fibroblasts and endothelial cells. The cytokine SCF plays an important role in the survival and proliferation of hematopoietic cells, melanocytes and germ cells, their migration and differentiation.

Devices of a new generation, automated stations of continuous radiation monitoring Zastava-1 are designed to organize continuous effective monitoring of the radiation situation and notification of radiation hazards. The stations have up to three independent measurement channels, which allows monitoring simultaneously in several zones. The stations support remote monitoring - they have a connection to a local computer network, Internet access.

DPSS lasers of the KLM-405/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes. Technical specifications Radiation output power: up to 10W Radiation wavelength: 405 nm Output beam diameter: 1.5mm Divergence of the radiation beam: 1.3 mrad Instability of radiation power: 5% Type of modulation: TTL or analog Time to enter the mode: 15min Spectral line width: 0.1nm

The MS-1104E spectrometer is characterized by high performance and accuracy of Mössbauer measurements achieved through the use of “compressed” geometry, as well as the use of highly efficient and selective resonant scintillation detection units that improve the energy resolution of resonance absorption lines by up to 30%. The technique of software and hardware stabilization of the spectrometric path developed and used in the spectrometer allows for long-term Mossbauer measurements without manual adjustment. The method of modulation in the specified speed intervals can significantly increase the sensitivity and expressiveness of measurements and reduce the time to determine the magnitude of the effects of resonant absorption by tens of times in the study of temperature phase transitions with a low concentration of resonant elements. The electronic components of the spectrometer are developed on the basis of a modern element base using programmable logic matrices and microprocessors. Adjustable spectrometric paths and high-voltage power supplies of the PMU are integrated into detection units, modulator driver modules and multi-channel storage are made in the ISA standard and are located in the processor unit of the computer. Setting and monitoring of all parameters of the spectrometer and processing of the measured spectra is carried out from the operating windows of the control and processing programs. Since 2000, more than ten spectrometers of this type have been supplied to leading scientific organizations in Russia and neighboring countries. One of the few industrial applications of Mössbauer spectroscopy should be noted - the development and supply to the Volgodonsk NPP of certified MS-1104Em methods and spectrometer for monitoring corrosion processes in the heat exchange circuits of the VVER-1000 reactor.

THe Kors NV-1250 SHV-BC laboratory fume cupboard is a single—frame cabinet with a width of 1240 mm and with a table top made of monolithic ceramics. External dimensions of the cabinet (W×D×H): 1240×700×1960 mm. Dimensions of the working area (W×D×H): 1208×660×1072 mm. Table top: monolithic ceramic. Convenient fume cupboard for comfortable work in the laboratory The table top made of monolithic ceramics is moisture-resistant, perfectly withstands high temperatures. Due to the lack of seams, ceramic granite tiles are better resistant to chemicals and heat. It is possible to place high-temperature equipment on it. The working area is closed by a single lifting frame with a counterweight. There are two exhaust zones in it: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1208×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm it will be 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, when the glass is raised, the height of the cabinet will be 2470 mm. The working area is illuminated by a fluorescent lamp (included in the package). The switch is located on the right side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets have the IP20 degree of protection, maximum load: 1.5 kW. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard 16 mm thick) are edged on the facade with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor. And if we need a cabinet for muffle furnaces? If you need a cabinet to accommodate high-temperature equipment, you might be interested in the ballscrew models. The depth of the countertop is specially increased so that you can put an oven or a cabinet.

An oxygen adsorption station for refueling cylinders is a set of special equipment designed for the production and subsequent refueling of oxygen into cylinders or monoblocks obtained from atmospheric air by short—cycle non-heating adsorption. Unlike the installation, the station is equipped with an oil-free booster compressor, which creates the necessary pressure. Put the squeeze on the compressor. Provita's adsorption stations allow producing oxygen with a purity of up to 99.0%. As a rule, the filling of production gas into cylinders is carried out up to a pressure of 150-200 bar. Composition: 1. Air compressor 2. Dehumidifier 3. Main filter block 4. Air receiver 5. Oxygen generator 6. Oxygen receiver 7. Oil-free booster compressor putting the squeeze on 8.Gas filling ramp

It is intended for the study of periodic electrical signals by visual observation and measurement of their amplitude and time parameters on the scale of the CRT screen in the frequency band 0-50 MHz, as well as for monitoring the parameters of two- and three-pole devices using a component tester. Technical specifications: Number of channels 2 Bandwidth 0 - 50 MHz Deviation coefficients of 2 mV/div - 20 V/div (step1-2-5) Installation error ± 3%, ± 4% with a 1:10 divider Rise time of PH <= 7 nsec Input impedance is 1 mOhm/25 pF, with a divider of 1:10 - 10 mOhm/23 pF Harsh operating conditions (-10°C to +40°C) Bandwidth 0 - 50 MHz Two channels Indication of deviation and sweep coefficients on LED matrices Tenfold stretching of the sweep Calibrator 0.6 V, 1 kHz (± 1%) X-Y mode Built-in Component Tester Screen 80x100 mm Weight 6,8 kg

Detection of SCR in all possible range of its characteristics High reliability Self-monitoring of components Backup power supply Recording and storage of measurement results in the non-volatile memory of the device The possibility of integration with external security systems DRG-AT2331 together with SRK-AT2327, personal computer and software "SARK.NET " allows you to form an alarm system for detecting the occurrence of a self-sustaining chain reaction (SAS SCR).

Island table Combined work surface: main countertop KG (porcelain stoneware) 650 mm deep / auxiliary countertop made of TRESPA material 200 mm deep / main countertop KG (porcelain stoneware) 650 mm deep Length, mm: 1800 Depth, mm: 1500 Height, mm: 900 BASIC EQUIPMENT The base is a collapsible metal frame made of rectangular steel profile, painted with powder paint (RAL 7035) with the texture of shagreen leather Four easily removable screens (RAL 7035) and two non-removable (RAL 5023) Hidden fasteners Adjustable supports (0-40 mm) A set of end boxes-plugs

The LOIP LT-117a modification device consists of an immersion thermostat-circulator LOIP LT-100 and a working bath with a flat removable lid. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +100 with tap water cooling °C Tvods+5 ...+100 Accuracy of temperature maintenance, °C ± 0.1 The error of setting the set temperature, no more than ° C ± 0.2 Heater power, W 1900 Pump: max. flow rate, l/min 7.5 pressure, 0.17 bar Bath volume, l 17 The working fluid is water, water-glycerin mixture. Open part of the bath / depth, mm 360x296/150 Overall dimensions, mm 535x335x370 Weight, kg 13

Furniture for laboratory work. The mezzanine is high to the storage cabinets Length, mm: 800 Depth, mm: 500 Height, mm: 700 PACKAGE CONTENTS housing – white melamine with a thickness of 16 mm facades – white melamine, ABS edge dark gray 1 compartment without locks 1 removable shelf (height adjustment at 3 levels) the permissible load on the shelf is 20 kg the handle-bracket is dark gray 128 mm, polypropylene.

The LOIP LT-412a modification device consists of an immersion thermostat-circulator LOIP LT-400 and a working bath with a flat removable lid. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +200 with tap water cooling °C Tvods+5 ...+200 Accuracy of temperature maintenance, °C ± 0.01 The error of setting the set temperature, no more, °C ±0.02 Heater power, W 2200 Pump: max. flow rate, l/min 6...12 pressure, 0.4 bar Bath volume, l 12 The working fluid is water, silicone oil. The open part of the bath / depth, mm 190x296/150 Overall dimensions, mm 355x335x350 Weight, kg 11.8