Search

The digital contact thermometer TK-5.01MS is designed to measure the temperature of liquid, bulk meterials by direct contact of the probe with the measuring object. The digital contact thermometer consists of an electronic unit and a non-replaceable submersible probe. Thermoelectric converters (TP) with NSH according to GOST R 8.585 are used as a thermosensitive element in the probe. •

Laboratory equipment for 0.4-10 kV cable lines and cable lines made of cross-linked polyethylene (ETL-10/SNH) 1. Test facility • – Maximum rectified voltage up to 70 kV; • – Maximum AC voltage of the industrial frequency of 50 Hz to 50 kV. 2. SNCH test facility • – Sinusoidal 0-24 kV peak, symmetrical (error ± 1%); • – Rectangular 0-30 kV peak, symmetrical (error ± 1%); • – Constant 0-30 kV of both polarities (error ± 1%); • – Output current 0-30 mA resolution 1 ma (error ±1%); • – Resistance range 0.1 Mohm -15 Mohm; • – The frequency of the output signal is 0.01-1 Hz in increments of 0.01 Hz, automatic frequency selection. 3. Burning installation • – Maximum voltage up to 30 kV; • – Maximum current up to 80 A; • – Working hours are not limited; • – Switching of stages is carried out without breaking the arc at the time of switching; • – The ability to start working from any stage of burning (when working with low–voltage cables); - Built-in afterburning. 4. High voltage pulse generator • – Output voltage 0...12 kV / 0...24 kV; • – The pulse energy at each stage is 3000 J; • – Built-in IDM for collaboration with the reflectometer. 5. Reflectometer – Supports 3 methods of determining the location of damage: • – By pulse reflectometry; • – By the method of oscillatory discharge; • – Pulse-arc method. 6. High-voltage cable detector • – Determining the location and depth of the cable at a depth of up to 10 m; • – Tracing at a distance of up to 10 km; • – Search for live electrical cables; • – Search for places where the pipeline and cable intersect; • – Determining the places of damage to cable lines; • – Site surveys before excavation; • – Search for places of damage to the external insulation of the cable; • – GPS\GLONASS coordinates recording and mapping of found communications; • – Cable selection from the bundle; • – Search for the place of damage by acoustic method. 7. Autonomous gasoline generator • – Rated power 7.5 kVA.

The kit is designed to control the temperature and pressure at the points of water sampling of hot water and HVAC systems, archiving the measured results for the purpose of their further documentation and analysis. The TSTP-M kit allows you to record changes in temperature and pressure directly at the points of water intake of hot water and HVAC, for a long period. With the subsequent transfer of data recorded in the device's memory to a computer, for printing a report, graph, etc. Features of the CHU-M kit The CHU-M kit allows you to control the pressure and temperature at the hot water and HVAC disassembly points. The kit consists of a four-channel meter recorder, which allows you to store 15,000 values in memory, for each channel with an interval of 5 seconds. up to several hours, which allows you to take measurements and store data for up to 1 year.

The KN-2-100-22 Primelab flask is ideal for a wide range of laboratory processes. Including for mixing, heating, cooling, storage, etc. At the same time, it is chemically and thermally stable, has a long service life, is suitable for intensive use and sterilization in an autoclave. The conical shape ensures uniform heating throughout the entire base. With a wide base of 64 mm, the flask has a narrow neck of 22 mm with a rim. The height is 105 mm with a volume of 100 ml.

The automatic tracer pulse generator "AG-114.1" is designed to create propagating signals (vibrations) in the routes of hidden communications with the active method of tracerouting. The device creates an alternating sinusoidal current in the studied communication (constantly or in short-term parcels) necessary to determine its location. The features of the AG-114.1 generator The selected output power (5 W at 1...1000 ohms, 10 W at 1...500 ohms, 20 W at 1...250 ohms) is issued automatically. The ability to work on such high load resistances allows you to trace very extensive communications. Low power provides energy saving and small "readjustments" to neighboring objects, high power provides a high range of broadcast and detection. Three generation modes: pulse – the main high-efficiency mode with high intelligibility against the background of interference; continuous – an additional low-cost mode for short-term special measurements; three–frequency mode, which provides the selection of the optimal frequency on a remote receiver without switching the transmitter (generator). Three generation frequencies: 512 Hz, 1024 Hz, 8192 Hz. Lower frequency – less "readjustment" to neighboring objects, higher frequency – higher detection range. Unusually compact (190x140x80 mm), for such a high output power (20 W), the autonomous design is provided by the use of highly efficient technology "CLASS D (BD)" (pulse output power amplifier with an efficiency of 80%). As a result, one small-sized autonomous battery with a capacity of only 2.2 Ah provides pulse generation for >5 hours at maximum output power (20 watts). It is possible to work with "recharge" from the charger or increase capacity by connecting an external battery to increase the time resource.

The NV-2400 OH is a large island table with a superstructure that can be placed in the center of the laboratory and organize workplaces on both sides. Table top depth: 152 cm. It is designed for standing work: the height of the table top is 85 cm. Two lamps and four sockets are built into the superstructure on each side. External dimensions of the table (W×D×C): 2420×1520×1650 mm. Work surface for your tasks We offer tables with various work surfaces. Table Model: Tabletop NV-2400 OLH: Laminate. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents. This countertop does not tolerate strong heating or prolonged exposure to solvents, concentrated acids and alkalis. NV-2400 OKH: Porcelain tile. It is a practical solution for most chemical, biological, medical laboratories and workshops. You can put drying cabinets, baths and other heating devices on it. NV-2400 OSPH: Chemically resistant plastic. It is a good choice for training workshops, analytical and medical laboratories. It does not tolerate high temperatures well, heating devices should not be placed on the surface. NV-2400 OPH: Polypropylene. It is chemically resistant, being a specialized solution for chemical laboratories that work a lot with concentrated inorganic acids and alkalis. It is not resistant to high temperatures. A large table for convenient work in the laboratory The superstructure allows you to compactly place the necessary reagents and laboratory utensils next to the workplace. Its depth is 30 cm, and its height is 80 cm. This table has plumbing fixtures: two taps and two small sinks made of polypropylene resistant to aggressive chemicals built into the countertop. The diameter of the sink is 135 mm and the depth is 110 mm. The working area on each side is illuminated by two fluorescent lamps (included in the package). The switch is located on both sides of the superstructure. There are also two sockets, one of which is grounded. The sockets (with four on each side, there are eight of them in total) have the IP20 degree of protection, maximum load: 1.5 kW. On each side, three cabinets are built into the table, two with a hinged door and a shelf inside, the third one with three pull-out drawers. You can store there laboratory utensils or small stuff you need at hand. The side laminated panels of the table (chipboard 16 mm thick) are edged on the facade with a 2 mm PVC edge, which increases their impact resistance and mechanical strength. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor.

The NV-800 OH is the most compact island table with plumbing in the NV line. It can be placed in the center of the laboratory and organize two workplaces. The table top is 152 cm deep. A lamp and two sockets are built into the superstructure on each side. It is designed for standing work: the height of the table top is 85 cm. External dimensions of the table (W×D×H): 760×1520×1650 mm. Work surface for your tasks We offer tables with various work surfaces. Table Model: Tabletop NV-800 OLH: Laminate. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents. This countertop does not tolerate strong heating or prolonged exposure to solvents, concentrated acids and alkalis. NV-800 OKH: Porcelain tile. It is a practical solution for most chemical, biological, medical laboratories and workshops. You can put drying cabinets, baths and other heating devices on it. NV-800 OSPH: Chemically resistant plastic. It is a good choice for training workshops, analytical and medical laboratories. It does not tolerate high temperatures, heating devices should not be placed on the surface. NV-800 OPH: Polypropylene. It is chemically resistant, being a specialized solution for chemical laboratories that work a lot with concentrated inorganic acids and alkalis. It is not resistant to high temperatures. A table for convenient work in the laboratory The superstructure allows you to compactly place the necessary reagents and laboratory utensils next to the workplace. Its depth is 30 cm, and its height is 80 cm. This table has plumbing fixtures: a faucet and a small sink-drain made of polypropylene resistant to aggressive chemicals built into the countertop. Its diameter is 135 mm and its depth is 110 mm. The working area on each side is illuminated by a fluorescent lamp (included in the package). The switch is located on the left-hand side of the superstructure. There are also two sockets, one of which is grounded. The sockets (with two on each side, there are four of them in total) have the IP20 degree of protection, maximum load: 1.5 kW. The side laminated panels of the table (chipboard 16 mm thick) are edged on the facade with a 2 mm PVC edge, which increases their impact resistance and mechanical strength. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor.

• Description of the TECHNOAS Housing and Communal Laboratory o – Used for hydrodynamic flushing and emergency cleaning of sewage from sludge, sand, grease, household and industrial waste in sewer pipes. o – Determining the location of underground utilities. o – Search and tracing of metallic and non-metallic pipelines. o – Determination of leakage coordinates by acoustic method in underground pressure steel, cast iron and plastic pipelines of heat and water supply systems, regardless of the depth of their laying, the type of soil, determining the exact location of the pipeline and the depth of its occurrence. o – Search for manholes of wells under a layer of snow, soil, asphalt. o – Analysis of the technical condition of the internal cavities of pipelines with a diameter of 60-2000 mm.

The NV-1000 MOP is a large table with a deep sink made of polypropylene and with a built—in dryer for 18 seats. It is designed for standing work: its height is 85 cm. Assembled dimensions (W×D×H): 1000×600×1650 mm. The table top is made of laminated chipboard. It has a built-in Stegler WJH0357F polypropylene sink, its internal dimensions (W×L×H): 490×390×290 mm. The polypropylene is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents and suits perfectly for washing laboratory dishes. The package includes a stainless steel mixer with flexible 300 mm tap connectors and a siphon. The upper part of the inclined shelves of the dryer, on which dishes are placed, is covered with a polypropylene insert to protect it against water and reagents. The 18 pins are also made of polypropylene. The side laminated panels of the table (chipboard 16 mm thick) are edged on the facade with a 2 mm PVC edge, which increases their impact resistance and mechanical strength. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor. Advantages of NV-1000 MOP tables A wide table with a polypropylene sink and dryer for 18 dishes. An inexpensive solution for laboratories that value the reliability and durability of furniture. The polypropylene is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Application of NV-1000 MOP tables Tables of the NV series are used in laboratories of the widest profile: at food and light industry enterprises, in scientific and educational workshops, in chemistry classrooms, quality control centers, medical organizations and many others.

Alonge AIO-29/32-14/23-50 TS is a curved connecting element with a bend, manufactured in the glass blowing shop of the Primelab company in accordance with GOST 25336-82. It is characterized by chemical inertness and high wear resistance. The length AIO-29/32-14/23-50 is made from heat-resistant and chemically resistant glass. It has impeccable smoothness, due to which there is practically no precipitation inside after use. Specifications: • Coupling grind size - 14/23 • Core section size - 29/32 • The length of the lower part is 20 mm with a total length of 50 mm • Outlet diameter – 9 mm • Tilt angle - 105°.

Колба коническая Кн-2-50-34 Праймлаб – незаменимый аксессуар любой биологической, химической и прочих лабораторий. Несмотря на компактные габариты, имеет удобную форму в виде устойчивого основания (51 мм) и узкого горла (34 мм). Рассчитана на работу с жидкостями, объем которых не превышает 50 мл. Общая высота колбы равна 85 мм. Выполнена из прочного боросиликатного стекла.