Search

The LA-160 nitrogen filling trap is installed on the inlet flange of the diffusion pump and is designed to reduce the flow of working fluid vapors into the pumped volume by condensing them on the elements of the freezing device cooled with liquid nitrogen.

ConFlat (CF) standard connections are used to ensure the connection of components of vacuum systems operating in the field of high and ultra-high vacuum.

Mineral vacuum oil VACMA OIL 300 is made from high-quality base components with a composition of additives that improve operational properties, such as anti-wear, adhesive, anti-shock, anti-corrosion, demulsifying, anti-foam. The VACMA OIL 300 is used for vacuum booster steam oil pumps. The VACMA OIL 300 mineral vacuum oil is designed to work at a maximum of 80°C. If the temperature is increased to 90°C, the oil life will be reduced by half, if it is operated at very low temperatures, then water vapor can condense in the pump, thereby worsening the lubricating properties of the oil.

ConFlat (CF) standard connections are used to ensure the connection of components of vacuum systems operating in the field of high and ultra-high vacuum.

The LP-250 flow-through water trap is installed on the inlet flange of the diffusion pump and is designed to reduce the flow of working fluid vapors into the pumped volume by condensing them on the cooled elements of the freezing device.

ConFlat (CF) standard connections are used to ensure the connection of components of vacuum systems operating in the field of high and ultra-high vacuum.

The 2NVBM-160(R)/1000 booster pump is a structure consisting of housings, a steam pipe, a trap and a heater. The alignment of the steam line in the 2NVBM-160(R)/1000 pump housing is carried out by a rod inserted into the hole of the hood (oil reflector) and screwed into the upper part of the steam line. The required effective speed of action of the pre-vacuum pump (pumps) at a pressure of 93 Pa (0.7 mm Hg) at the outlet of the booster pump 2NVBM-160(P)/1000 is not less than 15 l/s. The maximum residual pressure of the 2NVBM-160(P)/1000 pump, measured by the PMI-2 manometric ionization converter with nitrogen filled into its trap, is no more than 1.3×10-3 Pa (1×10-5 mm Hg). The pressure of cooling water at the inlet to the 2NVBM-160 pump should be from 0.2 to 0.5 MPa (from 2 to 5 kgf/cm2). The drain from the pump must be free with a jet break. Cooling water consumption is 145 l/h. The total amount of working fluid for the 2NVBM-160(P)/1000 pump is 5 liters., the level of working fluid should be between the upper and lower risks of the level gauge. Replacement or refilling of the working fluid depends on the operating mode of the pump (inlet pressure, pumping duration, etc.) and the composition of the pumped medium, so the time after which the working fluid is replaced or refilled can be 100 hours or more. A large flow rate of the working fluid is observed when the pump is operating in the input pressure range from 1.33 to 13.3 Pa (from 1·10-2 to 1·10-1 mm Hg). The operating mode of the pump in the range from 13.3 Pa (0.1 mmHg) to the maximum residual pressure is cyclically irregular.

The 3VVN2-50(H) water ring vacuum pump is not intended for use in fire and explosion hazardous industries. The 3VVN2-50(H) vacuum water ring pump is manufactured in the climatic version of UHL 4 and O4 (i.e. for moderate and cold climate) according to GOST standard 15150-69, meets the requirements of technical specifications TU 3648-053-00218526-2013, designed and manufactured taking into account the requirements of GOST R 52615-2006.

The LP-400(R) flow-through water trap is installed on the inlet flange of the diffusion pump and is designed to reduce the flow of working fluid vapors into the pumped volume by condensing them on the cooled elements of the freezing device.

The working fluid of the pump is water. These pumps are designed to work with liquids as well as gases and vapors slightly soluble in them that are not aggressive to the materials of the 2VVN1-3M pump design, not explosive and non-toxic. The use of a 2VVN1-3M(H) water-ring vacuum pump for pumping out water-gas mixtures is allowed only if the bulk of the water is separated and discharged at the pump entrance. Failure to comply with this requirement may lead to unacceptable overload of the electric motor and destruction of the working bodies of the 2VVN1-3M(H) pump. The vacuum water ring pump 2VVN1-3M (H) is manufactured in the climatic version of UHL (i.e. for moderate and cold climate) 4 and O4 according to the GOST standard 15150-69, meets the requirements of technical specifications TU 3648-015-00218526-2000, designed and manufactured taking into account the requirements of GOST R 52615-2006. Electricity grid must meet the requrimemnts of GOST 32144-2013

Size of DN: 10,16,20,25,32,40,50. Crimping rings (aluminum) for rings with high sealing capacity.