Search

A table with an overall height of 1860 mm with a table top made of MDF with a plastic coating. It is designed for long-term operation, the power frame does not contain aluminum and plastic parts in the fasteners. Overall dimensions without superstructure 900x640x760 mm Overall dimensions with superstructure 900x640x1700 mm

The 2NVBM-400(R)/6000 booster pump consists of housings, a steam line, a trap and a heater. The required effective speed of action of the pre-vacuum pump (pumps) at a pressure of 200 Pa (1.5 mm Hg) at the outlet of the booster pump 2NVBM-400(R)/6000 is not less than 45 l/s. The maximum residual pressure of the pump 2NVBM-400(R)/6000, measured by the PMI-2 manometric ionization converter with nitrogen filled into its trap, is no more than 6.6 × 10-4 Pa (5 × 10-6 mmHg). The pressure of the cooling water at the inlet to the pump 2NVBM-400 (R)/6000 should be from 0.2 to 0.5 MPa (from 2 to 5 kgf / cm2). The drain from the pump should be free with a jet break. Cooling water consumption is 600 l/h. The total amount of working fluid for the 2NVBM-400(R)/6000 pump is 47 liters, the level of working fluid should be between the upper and lower marks of the level gauge. Replacement or refilling of the working fluid depends on the operating mode of the pump (inlet pressure, pumping duration, etc.) and the composition of the pumped medium, so the time after which the working fluid is replaced or refilled can be 100 hours or more. A large flow rate of the working fluid is observed when the pump is operating in the input pressure range from 1.33 to 13.3 Pa (from 1 ·10-2 to 1 ·10-1 mm Hg). The pump operating mode in the range from 13.3 Pa (0.1 mmHg) to the maximum residual pressure is cyclically irregular.

BASIC EQUIPMENT Working box front guide posts – aluminum profile painted with powder paint (RAL 7035/RAL 5023), in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) front anti–spill side - polypropylene working surface - polypropylene 15mm thick removable plate 600*600mm with a ceramic granite work surface for placement heating plates (2 pcs.) 2 dependent lifting screens filled with transparent PVC, 5mm thick in a polypropylene frame in the lower screen – sliding doors made of transparent PVC with a thickness of 5mm lifting 0-780mm, does not change the dimensions of the cabinet when lifting the counterweights are placed in the front pillars-pylons and are easily serviced upper fixed screen – polypropylene inner part the working box is a fully sealed polypropylene capsule with a back wall washing system, a drainage channel and a polypropylene pipe for cold water 3 levels of hoods easily removable polypropylene exhaust canopies polypropylene drain sink on the top panel are placed: LED dust- and moisture-proof lamp (2X22W IP65) separated from the workspace by transparent PVC switching box with automatic emergency power off 16A flange with damper plug for air inflow d=200mm flange with aspiration collector for air outflow d=250mm (distance from the rear panels up to the center of the flange – 155mm) cabinet ventilation system

Technical specifications Overall dimensions of the device (mm) 113*25*14 The service life of the built-in battery is at least 300 cycles within the warranty period of the device. The sensitivity anisotropy according to Cs137 (%) is not more than 30 The full charge time of the built-in battery from the USB port of the PC or charger is no more than 4 hours. Operating time Continuous operation from a fully charged built-in battery in conditions of natural radiation background: - without the use of sound/vibration alarm for at least 2 months; - without using wireless communication and sound/vibration alarm for at least 4 months. Maximum counting speed (imp/sec) 10000 The weight of the device (g) is not more than 50 Note The Atom Fast 8850 can use a cylindrical crystal with a diameter of 10 mm and a height of 40 mm without prior notice. The energy range of the recorded photon radiation (keV) is not less than 60 - 3000 keV Working size of the scintillation detector (mm) 8*8*50 The scope of delivery USB cable for charging the built-in lithium-ion battery 1 pc. Dosimeter set—top box Atom Fast - 1 pc. Packing box 1 pc. Carrying case — 1 pc.

NV-1500 O is an island table with a superstructure that can be placed in the center of the laboratory and organize workplaces on its two sides. Table top depth: 152 cm. It is designed for standing work: the height from the floor to the table top is 85 cm. A lamp and two sockets are built into the superstructure on each side. External dimensions of the table (W×D×H): 1520×1520×1650 mm. Work surface for your tasks We offer tables with various work surfaces. Table Model: Tabletop NV-1500 OL: Laminate. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents. This countertop does not tolerate strong heating or prolonged exposure to solvents, concentrated acids and alkalis. NV-1500 OK: Porcelain tile. It is a practical solution for most chemical, biological, medical laboratories and workshops. You can put drying cabinets, baths and other heating devices on it. NV-1500 OSB: Chemically resistant plastic. It is a good choice for training workshops, analytical and medical laboratories. It does not tolerate high temperatures well, heating devices should not be placed on the surface. NV-1500 OP: Polypropylene. It is chemically resistant, being a specialized solution for chemical laboratories that work a lot with concentrated inorganic acids and alkalis. It is not resistant to high temperatures. A table for convenient work in the laboratory The superstructure allows you to compactly place the necessary reagents and laboratory utensils next to the workplace. Its depth is 30 cm, and its height is 80 cm. The working area on each side is illuminated by a fluorescent lamp (included in the package). The switch is located on the left-hand side of the superstructure. There are also two sockets, one of which is grounded. Sockets (with two on each side, there are four of them in total) have the IP20 degree of protection, maximum load: 1.5 kW. Two cabinets are built into the table on each side, one with a hinged door and a shelf inside, the other with three pull-out drawers. You can store there laboratory utensils or small stuss you need at hand. The side laminated panels of the table (chipboard 16 mm thick) are edged on the facade with a 2 mm PVC edge, which increases their impact resistance and mechanical strength. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor.

The vacuum condenser type trap with a capacity of 12 liters is designed to condense vapors of non-aggressive gases on the internal cooled surfaces of the trap, in order to prevent them from entering the pump.

Designed for collecting, storing and distributing purified water obtained by various purification methods, with a capacity of 100 liters and 100% stainless steel, which allowed for a long service life. Dimensions in terms of 560x580 mm Weight 13.5 kg

The ZVPlE-500 shutter consists of a housing with connecting flanges, a shutter mechanism, a lip seal to ensure the tightness of the drive element, cover, and electric drive. The shutter mechanism consists of a carriage, an upper and lower flap, which are pulled together by springs and balls. The carriage moves along the housing guides on bearings. The ZVPlE-500 shutter is opened and closed both by electric drive and manually using a flywheel. To switch to manual control mode, there is a switching device on the electric drive. The manual drive is used to adjust and regulate the shutter. ZVPlE-500 valves are manufactured in climatic versions UHL (i.e. for moderate and cold climate) and O (i.e. general) 4 according to GOST standard 15150-69.

The LOIP LT-212a modification device consists of an immersion thermostat-circulator LOIP LT-200 and a working bath with a flat removable lid. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +200 with tap water cooling °C Tvods+5 ...+200 Accuracy of temperature maintenance, °C ± 0.1 The error of setting the set temperature, no more than ° C ± 0.2 Heater power, W 2000 Pump: max. flow rate, l/min 10.5 pressure, 0.27 bar Bath volume, l 12 The working fluid is water, water-glycerin mixture, silicone oil. The open part of the bath / depth, mm 190x296/150 Overall dimensions, mm 355x335x370 Weight, kg 10.2

The NV-1500 SP is a large inexpensive desk with a tabletop width of 1500 mm. It is designed for routine office work in the laboratory. The height of the table is 75 cm (like that of a regular office desk). The whole desk is made of laminated chipboard (chipboard 16 mm thick) and edged on the facade with a 2 mm PVC edge, which increases its impact resistance and mechanical strength. In the right-hand side cabinet there are three drawers for storing papers, office and other necessary trifles, and in the left-hand side behind the swing door there is one removable shelf. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor. Dimensions of the table when assembled (W×D ×H): 1500×600×750 mm. Advantages of NV-1500 SP tables An inexpensive solution for laboratories that value the reliability and durability of furniture; A wide desk on which you can spread out all the papers; It is convenient to work while sitting: the height of the work surface is 75 cm, like that of a regular office desk. Application of NV-1500 SP desks Tables of the NV series are used in laboratories of the widest profile: at food and light industry enterprises, in scientific and educational workshops, in chemistry classrooms, quality control centers, medical organizations and many others.

The tripod is made of aluminum, which allows them to be sterilized at any temperature; this material provides lightness and durability. It can be used in water baths. The tripod has an individual packaging. Designed for storing test tubes.